Other Network Architecture Subjects

greetings. i am still a fledgling CCNA...i have inherited a rather interesting "mess". i have clients plugged into a 6000 series switch. however the cables are a mess and a half...and no documentation too boot. i am trying to figure out which ip addr...

Can't seem to route an IP (i.e. e-mail server's IP) from one location's router through another router. So, one client sits on one side of a router, and needs to go through the next router in order to get to the e-mail server. Any thoughts?

I'm in the process of connecting several frame connection to a single ATM connection. What information do I need to make this happen.Carloscdetirado@campusmgmt.com

Hello,if I have the following routes in place:ip route 10.1.1.0 255.255.255.0 serial0/0 1ip route 10.1.1.0 255.255.255.0 bri0/0 2If the serial is up, it will be routed out the serial. If the serial goes down, will this route out the bri interface un...

I am using 11 of the 13 slots so the cat 5 and fiber is beginning to look like a web below the 5500 going into the floor. I was wondering if anyone could give me some examples of the types of cabling management they have used with this beast? Or can ...

Hi,I can connect my 801 to my 2610, it works well. But when I try to call my 801 from my 2610 it does not work, disconnecting after 3 seconds.The debug isdn Q931 shows :- on my 2610 : DISCONNECT pd = 8 call ref = 0xF5 Cause i = 0x879...

I know the L3 card has G1/G2 which are the external ports and then G3/G4 which are the backplane ports. What I am wondering is if I can do any sort of trunking or something to use a couple of those Cat 5 ports in the layer 3 card, or like trunk G3 to...

We resell DSL service from a wholesaler and we want to use PPPoE. The DSL circuit is ATM and our aggregate circuit is Frame on a 7120. Has anyone had any luck with this?

A)-------------------------------------------------Catalyst 2820 Management ConsoleCopyright (c) Cisco Systems, Inc. 1993-1995All rights reserved.Ethernet address: 00-C0-1D-80-6F-79-------------------------------------------------1 user(s) now activ...

HelloI have a design question. I have two 5505 with RSM in each that are connected to each other with 200Mb trunk. Right now RSM of the first switch is in VLAN 1; RSM of the second switch is in the VLAN 2. Altogether I have about 20 VLANs. I am ...

what can i do to solve this???

Greetings,I have two 2500 series routers with BRI/NT1. I am trying to set them up in a lab scenario using a Emutel ISDN switch simulator. Everything looks good up through layer 2. When I try and ping the other the remote side I get:%SYS-5-CONFIG_I...

Very basic question...What does the asterisk in the following 'show line' output for lines 65 and 66 mean?access03#sho line Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int 0 CTY - - - - - ...

Hello,I have a Cisco 3662 with 4 X T1.I would like to monitor the Voice activity with MRTG. - How is it possible to get the number of active calls? Witch OID should I use?- How is it possible to get the ANI, DNIS and duration of a call? (Reduced CDR)...

Hi, I am using a time-range based access-list in a Cat 6506 Switch with two RSM, but every time the access-list turns off (because of the time-range) it never turns on again!. If anyone could give me a hand i would appreciate it, Thanks