Hi Everybody,The issue concerne an IpSec connections between some points of sales (P.O.S) and they Headquarters (HQ).The HQ have a non-Cisco Remote Access Server (Checkpoint firewall) and have only one wan.All the points of sales are Cisco routers, ...
What is the difference between using a DHCP relay and ip helper address on a 3750? Does anybody have a a minimum configuration to get either of them working?
I have a Cisco SG300-28p switch (call it NEW SWITCH) that I want to add to a Catalyst switch (call it OLD SWITCH) so it can pass one specific VLAN 500 to all the ports and they can get internet access like any other port. The problem is that NEW sees...
I am looking at building a PCB to install an ESR6300. I see it has 6 GigE interfaces (2 route / 4 switch). I am trying to find a supporting document to discover if the default naming is G0/0-G0/5 or something else. I assume G0/0-G0/5, but I want to v...
HelloI was performing security health check for Nexus 7 K and one of the control is " TCP and UDP Small Server" is enabled on Nexus 7K.What is the command to verify if TCP and UDP Small Server is enabled ? Thanks in advance.Srinivas Patnaik
Hello everyone, I have a relatively simple question but I can't find the answer anywere. Does anyone know which layer 2 protocol is used when connecting to a cisco device using a console cable? Thanks in advance, Regards Daniël
Hi there folks.I understand that Cisco is dropping support for DLSW and SNASw. It is no longer supported on new routers and older 2900 series will have no more updates after December this year.Is there a simple drop in replacement for Cisco DLSW or S...
Hello,I’m trying to set-up one of my WAN pppoe broadband connections (FTTH) into my new RV340W Router, but I can’t figure out how to establish the custom VLAN+QoS requirements for this particular ISP. More precisely, I need to tag my upstream traffic...
Hi All.We have a 6509 and configured 4 interfaces bundle together into 1 port-channel. We are seeing 1 of the port having more output drops than the other 3. What would be the issue? How to make the output drops decrease? If we set the port with "hol...
Hi, i am trying to configure cisco nexus 5548UP with GLC-LH-SMD 1g sfps after changing the speed of the port the port came up and reason shows none. but there is no communication between the ports. do i have to do any other configuration, also i saw ...
I have a 2951 ISR with a HWIC-4T Serial Card installed. We are connecting it to a Synchronous Serial device where the Data & Clock signals are provided externally. There is a custom encapsulation on the data stream. Is it possible to stream the da...
I have a question about "clock set" command on Cisco switch: I did a "clock set 20:37:00 pst -8 21 march 2005" but when I do a "show log", it shows different time: March 22 4:39:00. Please the followings:switch-sanmateo#sh clock20:37:05.847 pst Mon M...
I am developing a script that performs a WA to avoid the loss of the configuration in the cEdge when I upgrade the IOS on SD-WAN.The script performs the following actions:cEdge#del /force bootflash:sdwan/ios.clicEdge#del /force bootflash:sdwan/sdwan....
HiI am setting up a router and keep getting this message,00:15:23: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?HOw do I stop it Thanks
Hello guys i just started Wireless concepts on Netacad, i wanted to setup WLC controller, but as soon as i enter the configuration via browser, it says on almost every options that it's not supported in PT, i am using latest version. I tried differen...
