Sho int cap: Queuing: rx-(N/A), tx-(1p3q1t, Shaping)So there are 1 strict prty Q, 3 std Q and 1 Threshold. But in the Interface config, only TX-Queue 3 can be 'priority high'. Q.1 Why ? Q.2 Is #3 the 'strict priority Q ? Q.3 How to assi...
HiI search a tools to detect on witch switch and on witch port are connected a client by his mac address ( in a cluster switch environement as well on standalone switch)I must rebuild my patch pannel diagramm and detect free port and free outlet in o...
Hello,Would appreciate very much if somebody could help me understand this!Had a problem where 2 printers were on the same subnet and vlan. One printer responded to ping from the Layer 3 core switch on the LAN. The other printer did not. Thats not...
We have a couples of new 6500-e (SU 720)with CME T1 modules on itI can not see the configuration and "show hard", but it show on "show module". Also, I can sess into the module.Anyone knows about why I can not make configuration changes via console p...
Hello,I'm really confused about LACP and PAGP.I've set an etherchannel between my 2 switches, and the modes avaiable are:on (no protocols)PaGPLACPNow, I wasn't able to find a decent document able to explain me what PaGP and LACP give you more than st...
Hi,Can anyone tell me if i use a 3750 using 1000Base-sx SFPs connected to another manufacturers fiber switch that only runs at 100MB , will this work.I can't seem to find out if the 1000Base-sx sfp's run below 1000MB.ThanksMark
I have an issue with poor response times to my 2950 switches. Is this a buffer issue.#sh buffersBuffer elements: 498 in free list (500 max allowed) 15748070 hits, 0 misses, 0 createdPublic buffer pools:Small buffers, 104 bytes (total 60, per...
Hi,we had a network with Cat4500 SupV as Core and Cat3750/Cat3750G (not metro!) as Distribution platform.I'm finding out if using VRF Lite is possible to separate two entities that use the same physical network and span the whole net to have one, ma...
Can anyone advise me of which one is the best to use, I generally use eigrp, do many people use rip, igrp etc, Is there any big differences between them ?
Hello, has somebody an idea what can cause the following behaviour in that environment and how to eliminate thisEnvironment:Windows 2000/2003 servers, HP teaming, Cisco switch 2970 12.1(19)Issue:transfer of 1GB takes X secondstransfer of 2GB t...
I want to find out where PC with particular mac address is located on switch.from internet, i have found command traceroute mac .But only tracerote is coming ..help on same .,
hi.I am config ip accounting at L3 mode of the c4006 switch.but I am not see on sh ip accountig.bleow message is presented.test(config-sub)#ip accoAccounting will exclude mls traffic when mls is enabled.why not see on ip accountig information?== mod...
I've Cat3550 and IP phones connected to it. I want to remark voice packets from ip prec=5( by default) to ip prec=3. I disabled mls qos trust device cisco-phonemls qos trust cosHow to do it?
I have Cisco's 2600 Series Router and 2 L3 3550 Series switch with 24 ports each. Around 12 VLANS are to be created and in couple of VLANS heavy traffics like video/media streaming will be taking place. Now, confused whether to use 2600 Router or the...
Anyone know how to get the IOS (I'm using 2801 with 12.4) to generate FECN's and BECN's when it's being used as a frame switch? It apparently doesn't do it by default.
