Hi, I have a problem an is when i use this command encapsulation ppp on the interface cellular 0 interface Cellular0 description ### Access WVPN ### ip vrf forwarding WAN ip address x.x.x.x x 255.255.254.0 ip access-group SUC-WVPN-IN in ip virtua...
Forum Posts
Hi AllWe have a MPLS network with a full mesh of gre tunnels.there are many spoke sites, with a main HQ.When we apply QOS to this WAN, what is the best way to ensure each tunnel gets the right qos treatment? Do you put bandwidth statement on the phys...
Resolved! Configuring BGP
Hi, We have two ISP links which are connected to a router then connects to a firewall. As shown in the below picture and we want to configure failover using BGP with the two ISP links. What configuration we need.
Hi all,Site A and Site B are connected with 2 links (1G and 100Mbps) and configured using OSPFv2.Site A and Site B equipment are from different vendors (SiteA is Cisco, SiteB side is non-Cisco) and we are worried that in the event of firmware upgrade...
Resolved! Strange Log
Please Kindly Help, I'm facing the one of strange log in my l3 switch devices that impact is made which connection through to that switch is going down. Please, someone explain to me about this issue and how to fix it. Captured log as below : 02521...
How is one-way PPP PAP configured? I have the following in my configurations. Server huss0036_L3_R3: hostname huss0036_L3_R3 interface Serial0/0/0ip address 203.168.190.9 255.255.255.252encapsulation pppppp authentication papclock rate 128000 Clien...
Hi,We have LTE backup connection on Huawei E3372 connected to USB2 port of RV320. Modem is not visible in RV320 and it is not known as compatybile with firmware 1.0.6 (https://supportforums.cisco.com/sites/default/files/rv32x_usb_compatibility13.pdf ...
Resolved! Setup connection(s) with ISP process??
If you have to setup a connection with an ISP that let's say will be sending your networks through their MPLS/BGP etc. cloud, how is that normally done? I am used to setting up more or point2point connections where I just point my DG to their directl...
See attached diagram diagram of lab topology. So OSPF 100 routes/interfaces communicate fine with BGP 65001, and likewise between EIGRP100 and BGP65000. But routes from OSPF and EIGRP are not being shared through the 2 BGP Autonomous Systems meaning...
Hello! Firstly, my apologies if my topic is on the wrong section of forum. I have create an internal network with my Cisco RV340W. This RV340W is connected at the internet service provider router and distribute the network in my house with some rules...
I've made an point-to-multipoint frame-relay network, one with typical hub and spoke. While each spoke's EIGRP routes are being shown in the routing table, connectivity can't be established. R1 (HUB)interface Loopback0ip address 1.1.1.1 255.255.255.0...
Yesterday, I tried using normal traceroute to see my hops to Google DNS. Every time I issued that command on my router, it would fail before hitting the internet. Even when I tried an extended traceroute, without a source, it would fail before gettin...
Hello.I am personally a little fresh to the engineering side of networking but have experience in setting up and troubleshooting networks that have been set up. I've been tasked with putting together a network for a campus where the on site admin has...
Resolved! 2 Routers are Unable to communicate.
Hi everyone,I would like to ask your suggestion/s on how to make my two routers communicate with each other. I tried using static default route but it did not work. I hope someone could help me. (Summary of what is happening in my lab simulation)ISP_...
| User | Count |
|---|---|
| 11 | |
| 11 | |
| 7 | |
| 6 | |
| 5 |
