Hi Guys What is the Replacement now from cisco with regard to GSS for the below A/A DCI Subject : optimize the inbound client to server traffic flows is DNS based and leverage the following components: •Cisco Global Site Selector (GSS) •Cisco Applica...
Forum Posts
Resolved! how to configure ACL on routers?
I am given a topology in which I have to apply ACL. The PCs in the left bottom side are not to be accessed by any other PCs. This was done successfully as follows: access-list 1 deny anyaccess-list 1 permit anyint fa 0/0ip access-group 1 out Now the ...
Hi Guys, Looking for a bit of advice. i,m task with splitting a company network into two separate sites. However, since starting, the goal posts have been slightly moved. They now need to temporarily router traffic (simple application data) between...
Resolved! Interface issue on ASA 5510
I have an issue where I need to add a backup route to my ASA. Currently I have Inside addressed in the 10.0.0.0/16 subnet (10.0.0.2) connected to the cable gateway (10.0.0.1). I NAT all IPs from inside (10.1.0.0/16) where the gateway PATs it. The pro...
Hello, Hope you all can help me understand where I've gone wrong here. I'm using Packet Tracer to study for my ICND2. Practicing ospf virtual links at the moment and things aren't quite working out. I have several routers in area 0 and the link betwe...
Resolved! VLAN routing to WAN
Hi, I have a Cisco 897VA connected to my modem (192.168.1.1) on GE8.My PC is connected on GE0 (vlan 10) and get a correct IP address (10.0.2.2). I can ping 192.168.1.240 but I can't ping 192.168.1.1 and I have no access to Internet. ip dhcp excluded-...
Resolved! CISCO 2800 Series Router Boot Error
When I boot the router, I get the following error. --------------------------------------------- System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc...
Hi All,I would like to ask about why vedio stream quality is drop on GRE over IPSec link.When i remove ip sec policy on physical link, quality is quite good.I got the problem even though i am using GRE tunnel only without ipsec encryption.Let me know...
Hi Everyone ,i have PPPOE server which is configured in Cisco router 3800 and Radius server , everything is working fine but the issue is when the user is disconnected from the PPPOE server the user remain stucking in radius server and the user will...
A few months ago, a problem appeared on my ARS9k-RSP4 with trident line card a9k-8t-l. IOS XR 4.2.3.I use only BGP functionality. My router receives two FW v4 + v6. The logs began to issue a message:LC / 0/0 / CPU0: Jun 8 15: 50: 57.033 fib_mgr [171...
Hi, This is the main question: How a VRF can advertise a route which is learned through iBGP to another VRF But let me elaborate it little more. First, explanation: I have created three VRFs under one router and one BGP instance. They are named L-VRF...
HiI'm trying to encapsulate ethernet in a gre tunnel (gre ethertype 0x6558 Transparent Ether Bridging)I saw the functionnality here :http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/interface/configuration/xe-3s/ir-xe-3s-book/ir-eogre.html#concept_F9...
Resolved! BGP Sync rule default ?
Hello BGP synchronization provides black hole prevention in IBGP environment.butcan anyone explain why " no synchronization" is default in Cisco routers ?. Thanks in advance.
Hi everyone, im currently configuring an AP, connected in a trunk port of a CISCO Switch,and i would like to know if it is possible for my guest users in the AP to get a different IP address range let say a 192.168.1.1 / 24 assigned, whithout a route...
I have a Cisco 3945E 15.4(3)M1 (Upgraded from a 2851) Router connected to the internet via a cable modem using dhcp. This router, in turn connects via a plain GRE tunnel to a cloud instance and on to the internet.The tunnel and endpoints are up and r...
