I have a ISR 4331. I've just upgraded the IOS to isr4300-universalk9.03.17.03.S.156-1.S3-std.SPA.bin. I've added a WIC card: vwic3-2mft-t1/e1. I'used the command: card type t1 0 1 and after a restart, the controller configuration was populated: contr...
Forum Posts
Hi Overseas Friends I have 1 Gig link between 2 sites , the PRTG shows the Link is fully utilized , i need to know What type of traffic eats up the whole 1 gig bandwidth thanks Ibrahim
I am trying to construct a given topology in which I have to configure the router for RIP.I am having a problem in configuration. I am using Generic Empty-PT Routers, Switches and End Devices. Following is my configuration: config thostname R1no IP d...
Resolved! 3925 SM-ES3G-16-P not recognized
We purchased an 3925 with a 16 port Gig SM module installed.When I boot up router, those interfaces do not show up. Do I have to do anything special to enable those interfaces to be seen on router.(The 4th Gig interface show up as GI1/0, but I don't ...
I am currently having an issue setting up PPTP session between 2 routers, i am currently simulating it attached below are my configs i took off from the router. Connection between routers would be established but keeps dropping every 2 minutes for so...
Hello, I understand that Standard ACLs are typically placed in the outbound direction and Extended ACLs are typically placed in the inbound direction but when due these change? In what real world scenario would an Extended ACL be placed in the outbou...
Hello everyone i was curious that how frame at L2 is converted into bits at layer 1 to transmit from one device to another. However i was not able to find any good point to say that "which technique,technology or protocol" helps the process of conver...
Hi All,I'm trying to relocate my lab rack to my basement, but want to keep one switch in my office. I've got a 2921 router, a 3750 switch, and a basic managed netgear switch. Everything is working fine, but I'm trying to duplicate the settings out ...
Situation: Currently we are using WCCP Redirects to point an entire subnet to a Riverbed device to optimize replication traffic. Recently we installed a Point to Point circuit to shift specific replication off of the WAN and onto this point to point...
Hi, I am having a strange issue. Strange because I have set this lab up at my colleges network and had no problems. Packet tracer also is ok... I'm starting to think that there is a problem with the router. Topology screenshot attachedBasically I h...
I have several questions about the Nexus 7K. I am attempting to connect to a Nexus 5548 using a 10Gig interface. I am using FINISAR 10Gbase-SR on both sides with 50/125um fiber. I am unable to get the interfaces up on either device. Is FINISAR a qual...
Smartphone0 to Cell Tower0Smartphone1 to Cell Tower1Smartphone2 to Cell Tower2 in 3G/4G819HGW to Cell Tower2 in 3G/4GPC14 connect(Wireless) 819HGW819HGW set DHCP to PC14 "200.200.200.0/24"Central Office Server0 set DHCP to Smartphone0~2 "172.16.1.0/2...
We have an application where a device needs to send packets or messages to two different destinations. The source device however is limited to only sending out one packet or message to one IP address. We have a Cisco series 3000 switch/router with IP...
Dears Experts i am always wondering how the DR is been setup for the HO employees and for Branch users, i will appreciate a lot for the person who has build a DR and and have done the drill for the same, lets assume the below. i have a collapsed cor...
Resolved! Static Network Route
I need your help, I am setting up a basic static route between two routers. The pc's cannot ping each other.PC1 can ping Router 1 and Router 2PC2 can ping Router 2 and Router 1WireShark on PC 1 sees the ping requests from PC 2, but PC1 does not repl...
