Hi, I wll be pleased to know if anyone guide me for how to STOP Eigrp, sending HELLO packets but keep on receiving? I just tried to use commands as follow: #access-list 1 deny any#router eigrp 1#distribute-list 1 out gig0/0 (I'm using gig0/0 as my ...
Forum Posts
Hi Guys,As part of a DMVPN over LTE network, I have a number of 1921's deployed, we have now purchased some 4321's and the existing 1921 configs are not working. Specifically, under the C0/1/0 interface on the 4321, encapsulation SLIP is no longer av...
Hi there,I need some advise, we have a new 1Gb carrier ethernet circuit between Madrid and Spain.When performing iPerf (v3.6) TCP testing we get 950mbps from Barcelona towards Madrid but Madrid to Barcelona we get no higher than exactly 201mbps. I ca...
Hi,Can someone please help me configuring RADIUS server.What steps required to complete the configuring of RADIUS server. Can i make my PC a RADIUS Client if possible then how to get this to work.Regards,Anon
Hi, I want to trace (lookup) all my traffic topology means packets going out from my PC to an internet user's PC. How can I find that at which point my traffic got dropped as I used tracert/traceroute for traffic map.Because I've one server on the in...
I've got 2 questions. 1) Can I remove a NIM-2MFT-T1/E1 module from an ISR 4351 without shutting the router down. I believe I might have to run an OIR command to shut the module down before removing it? And I believe I can remove it without shutti...
Dear experts, What would be the advantages of using OSPF + iBGP in simple 4-router topology (below) vs iBGP full-mesh between interface addresses ? Topology 1: OPSF enabled on transit links and loopback addresses iBGP established between loopbacks...
Hello All, We want to redistribute received routes from one provider e.g. SingTel to Telstra. Both been configured as same AS and peered with BGP. We are receiving route from SingTel e.g. 10.80.128.0/24 (Asia office subnet) and Telstra (Asia offi...
Hello,I'm facing an issue and I really don't know what's happening.I'm working on 2 Cisco routers (Cisco 891 and Cisco C1111-8P). The running-config is identical on both routers.I have a nat as follows. ip nat outside source static tcp 10.10.10.10 12...
Hi, I'm new to Voice routing n switching. I'm given a task to seperate voice and data traffice from Cisco IP Phones and laptops running softphone and route them through different ISP's (ISP 1 for Voice and ISP 2 for DATA) I'm thinking best approach f...
Resolved! Static NAT question
I have been following a NAT tutorial and I have a simple to ask.Assume there is only 1 IP 209.165.100.30 configured on g0/0and we want to NAT the IP 209.165.100.29 to the HoneyPot server, where and how are we going to set the IP 209.165.100.29 at? D...
Problem solved
I am currently trying to configure NAT for a network that needs a 192.168.x.x private for a dhcp server and a few other VMs and I don't want it to leak out into the 10.10.x.x network. I need almost all machines in the 192.168.x.x to have internet con...
Hello I had a similar post trying to access 1 subnet from another going through my 5508-X but my approach was wrong. I was exiting 1 subnet into the ASA and then back into the other subnet via its WAN port but being that the 2nd subnet is on a VPN Tu...
This topic is a chance to discuss more about Enhanced Interior Gateway Routing Protocol (EIGRP) fundamentals. The session seeks to clarify the status and fundamentals of the EIGRP protocol. In addition, the experts will discuss the common steps used ...
