This might not be a valid question but I just do not have a 4451-X router available to verify... I got following when test configuration of BDI inside simulator. Router(config)#interface BDI208New BDI exceeds maximum allowed BDIs(5) The configura...
Forum Posts
Hello, So I just inherited this network. My goal is to get it configured with VLANs for various reasons. One of the main reasons is to isolate voice and data traffic and do some QOSing. All phones are Cisco branded / Linksys graduates :-) Every...
Dear All, I am pretty new to Cisco. I want to remove the dialer configured on Fast Ethernet 0/0 (WAN Port) and to put the ip address 192.168.10.10/24 on that port, which is coming from ISP with internet configured. Please help. Find the curren...
Resolved! Doubt about VSS
Hello team i have a doubt about the configuration of VSS. Let me explain, i have 4 6500 on VSS then i have 2 domain ID, but for a mistake i configured both with the domain ID 100, then both have the same virtual MAC ID, i going to change th...
Resolved! ISP Failover
We have a block of public IP address advertised from our ISP. We recently introduced another ISP for failover/loadbalancing purpose Do we need the new ISP to also advertise our IPs?
HI, I do have a problem on and ASR920. I configured two service instances on one physical interface for different .1q VLANs. Both instances attach the same device into the same bridge-domain. This is intended to be used for two euqal services fro...
I have a netwokr in which users are getting ip address from DHCP server that is window server.i want to block some users to access interent by using their device mac address.i have these devices in my network...2921 cisco cme routercisco 2960 switche...
hi guy I have question. if I've 2 cache such as 1. blue coat proxy 2. cache flow so I would like test specify source for deference the traffic to web cache this is example IP 1.1.1.1 to bluecoat IP 1.1.1.2 to cache flow I need exampl...
i am trying to create an ibgp connection that will advertise my local networks (if possible) to each other. The problem i'm running into is that i don't want to use ospf for one router to talk to another router to know about local routes. The one r...
Hello, does anybody have experience with connecting Cisco 3750X-12S-S (to 10G network module) to HP 5700 (JG896A) with HP X240 10G SFP+ DAC cable (JD097C)? Will it work? Thanks a lot Tom
Resolved! OSPF Wan Design question
Good evening everyone, I'm deploying an OSPF design and had a question or two: I'm going to be creating an area 0 for my corporate office, which will be my ABR, and plan on making my other sites area 1 or area 2 for each new site, maybe even just lea...
Hi all can anyone tell me, with mpls networks, we have our ce's thats connect to pe's my question is, do all pe routers in the isp's network peer with each other?
Hi all, I will try and explain this as best as I can, and with a basic flow overview: Cisco 2691 (PPP Client) --> Cisco 2691 (LAC) --> Juniper MX240 (LNS) Okay, with IPv4 set as a pool on the LNS everything works fine. I get an L2TP tunnel, authe...
Resolved! ASR 1002 does not support 4 octet ASN
Our Organization has bought BGP ASN 395xxx and we are using this ASN for BGP peering with cogent router and advertising our Public subnets to Cogent through BGP. In addition to this, we are also planning to peer one of our virtual router with black...
Hello all, I have been trying to configure a Cisco 877W router so that I can remotely access it via SSH, but I can not seem to get it to work. I have configured an IP address to VLAN 1 and I have even created another VLAN (VLAN 2) to make sure that I...
