Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

HiI have a rare case. switch 6500 make crash and go to rommon. when review the crash appear that the switch charge the configuration from nvram, but, at the ending there are a few line command, that make the switch go to crash.. then I have to bootin...

rc5295509 by Level 1
  • 1889 Views
  • 4 replies
  • 0 Helpful votes

Hi All ! On my ASR 1001 - X I done a simple Traceroute and got this as a result HostnameHere#traceroute 46.182.249.38 Type escape sequence to abort. Tracing the route to 46.182.249.38 VRF info: (vrf in name/id, vrf out name/id)   1 80.81.194.140 [A...

frazreid2 by Level 1
  • 1327 Views
  • 2 replies
  • 0 Helpful votes

All, We have a Cisco 4321 IOS-XR that we need to install a NIM-2GE-CU-SFP.  We currently have this image installed as of now. isr4300-universalk9.03.13.04.S.154-3.S4-ext.SPA.bin Will the above version support the module in italics above? Let me know,...

metzj by Level 1
  • 751 Views
  • 1 replies
  • 0 Helpful votes

Hi, We have two hubs and two spokes at each site, two hubs are for redundancy spoke 1 has tunnel 1 and spoke 2 has tunnel 2 and both are connected to both hubs.tunnel 1 has internal apps traffic hosted in hq and tunnel 2 takes branch office ip phones...

Hi everyone,  I got an C891F router, attched to two ISPs (first ISP : Up to 180Mbps , second ISP : speed s up to 70Mbps) I configured VRFs so each ISP serve different LAN  (2LANs one for the employes and the second for students)  So the problem is t...

Hakim RS by Level 1
  • 727 Views
  • 4 replies
  • 0 Helpful votes

So I'm soliciting advice where I need answers...here goes! I'm designing on-the-fly a DMVPN overlay. Each Branch ISR(4331's and 2911's) has 3 incoming WAN Connections. 1. MetroEthernet WAN provided by MPLS Provider 2. Internet via Local Cable Provi...

A church is currently using a non-business router with WiFi (non Cisco product).  I need suggestions for a non-WiFi router for this church environment: * about 12 staff members, 10 wired, 2 wireless, 4 printers (IP based) * uses web-based applicatio...

ACETech by Level 1
  • 849 Views
  • 5 replies
  • 0 Helpful votes

Hi, I have 3 Spoke CSR connected to central hub CSR Router over VTI Tunnel VPN/BGP. Spoke 1 and Spoke 2 has overlapping subnets 10.55.x.x/16 Spoke 3 is head office on 10.60.x.x/16 Hub CSR is 10.99.x.x/16 , so hub is sitting in middle of 3 Spoke. Al...

ahmad82pkn by Level 3
  • 3112 Views
  • 13 replies
  • 0 Helpful votes

Hello all, I have a Cisco 1941 Series with two separate BGP connections to my ISP. This is still in the testing phase so I can try everything I want. The Cisco announces a prefix to the ISP via both BGP sessions and in return the ISP (a Juniper MX r...

noc by Level 1
  • 538 Views
  • 2 replies
  • 0 Helpful votes

Hello,  Current NXOS release version on our NX7K is 7.3(0)D1(1). The next release version is 7.3(0)DX(1) and the next one up is 7.3(1)D1(1). My question is can I upgrade directly from 7.3(0)D1(1) to 7.3(1)D1(1) or do I need to do it in a sequential ...

zekebashi by Level 4
  • 348 Views
  • 2 replies
  • 0 Helpful votes

I have one outside, public interface with a single IP. That interface is in VRF INTERNET. I have two internal VRFs for GUEST and CONTRACTOR internet access that I need segmented. This is all separate from the global routing table for corporate device...

Hello, I recently had the requirement to change more than 200 Cisco NCS 5000 Series' hostnames. I tought in creating and execute some kind of script in order to complete this task within the minimum amount of time as possible. Can this be achieved? ...