Hi, Regard command "commit label PostN" in ASR9K has two meanings. One is to commit, and second is its label. My question is how to use its second meaning "label PostN"? Thank you
Hi, Regard command "commit label PostN" in ASR9K has two meanings. One is to commit, and second is its label. My question is how to use its second meaning "label PostN"? Thank you
Hi, We have been given /29 subnet by the isp. Can it be divided into still smaller subnets? Mahesh
Hi our DMVPN hub router is behind of internet firewall. and need to communicate with spoke router to establish IPSEC tunnel. my question is do we need to open bi-directinoal rule on internet firewall? I think DMVPN and SPOKE will initiate each other...
Good Morning, I am .from the Philippines, I have this Cisco RV042 from a friend 3 years ago and still working, I use this router mainly for dual wan purposes because i have two ISP, my problem since was when the other ISP will expire the Data because...
Hello everyone, we use a 2951 router with a EHWIC-VA-DSL-B card as our VDSL router. Is there any way to reconnect the DSL connection on a certain time of our choice (i.e. at night) other than just reconnect once at nightime and hope that the 24h rhy...
Please kindly assist advise, i wish to monitor bandwidth usage per vlan, on my switch. I dont seem to be getting OID's for vlans. Is there a way i can do this as snmp is not able to differentiate traffic per vlan.
Cisco 2811 (2MF-T1) -->T1 Patch Panel --- Over Radio --T1 Patch Panel--> Cisco 2811 (2MF-T1) Serial in down, Line Protocol is down. LP light is Blank, AL light is Orange and CD light is green. I have connected Card to T1 Patch panel using Crossover ...
CASE-STUDY - TWM 2 ISPs ISP1 for Emails in and out ISP1 for RDP in ISP2 for All Other Traffic (http/s) Redundancy on both Email to be hosted Internally Currently hosted outside ...
Hey all, Can I create route map to work if there is no reachability? I want to create route map that works only wen I can't get ping from my gateway to change my route to other ISP.
We have a Cisco 2851 router that we use for VOIP. We have 2 PRI's coming into the router. On the HWIC card, for controller one we have a yellow alarm light with a green light below it. On controller 2, we have the green light. We have been having...
Hello Network Gurus, I'm just the tech guy in our company and one of the network engineers mentioned that we will have a cutover to a new ASE 1gig circuit, he mentioned that he can do trunked VLAN or Routed interface. I'm kinda confused on what he ...
HI- Trying to pull down new IOS for a 4331 router. It keeps timing out. I'm using SolarWinds, which doesn't seem to be held in high regard. Can someone recommend another choice? Also, any other tips would be appreciate.
I would like to buy two routers and two cisco switches in order to realize a supervision application on these equipments as well as on the other appereils connected via the SNMP and SSH protocol. What materials do you advise me to set up my solution ...
Hi there, I am trying to find the reason for the high number of input-queue drops on a 2821: Input queue: 8/150/3790/0 (size/max/drops/flushes); Total output drops: 0 The interface concerned has CEF enabled: IP fast switching is enabled IP fast sw...
Plz Help me. I Have A new Router Cisco 2911, but when i conect fisrt time to Router by Console Command, i don't know how about to change the username and password, and i shutdown the Power system. Now i can't conect to the Router because the router ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-04-2025 12:04 PM | ||
| 12-04-2025 08:01 AM | ||
| 12-03-2025 07:46 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM |
| User | Count |
|---|---|
| 10 | |
| 6 | |
| 5 | |
| 4 | |
| 4 |