I'm working on a project in which I need to do something like, I'll monitor and collect traffic passing through a switch, then classify it based upon port number, packet size and maybe IP range too. Then I want to display this on a web page. The web ...
Forum Posts
Hello guys, how to restrict VTY access to a specific IP? For example: - Allow access from the private or local network - Allow access from a specific Public IP Is this doable? I'm following this link: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios...
Hello. May you please confirm my understanding?... GIVEN: an ASA5525 has a site-to-site VPN erected. The remote vendor subnet defined in this local ASA route-map ACL is 172.16.0.1 The Inside interface of this local ASA is 192.168.0.1/24 A local LAN...
Both WAN service are DHCP.... Please Help!! If you see anything else that I missed please let me know. Thanks in Advance. I have about 50 Ring Devices. Did not want issue with video and sound. Building configuration... Current configuration : 1257...
Resolved! DHCP not giving out addresses
Hello, Currently we have a Cisco 1921 router that is in a medium business setting.Data: 40 users, 6 WAP (1142's), 3560 48 port PoE switch, DHCP setup on the Cisco 1921 router, Spectrum business is the ISPAbout 3 weeks ago everything was working just...
Hello, I have a Cisco IE 4010 switch running IOS version 15.2(7)E2, and I'm attempting to set up HSRP for several VLANs. However, I'm facing an issue where I'm unable to add the virtual IP address for HSRP using the standby ip command as it doesn't a...
Hi all, We have a Cisco 892 and we are experiencing some performance issues.When testing using Iperf from LAN to WAN with speeds of 750Mbit/sec (packet size 1024K) we see packet loss when pinging the LAN ip address (Vlan 100) of the router.I was told...
Resolved! Network Design proposal for Bank
HelloI am new to Wireless Networks please help me with project. I am struggling with correctly constructing my network diagram.A network proposal has to be developed for a new bank called Wirenet bank. The bank will have a main office, which will be ...
hello ! There are two ISPs. ISP-1 is the main route and ISP-2 is the backup path.(ISP - Router all eBGP)Only Static Routing is available, and there are no other options. I'm trying to use Floating Static Route to set the main route and backup route,...
HiI can be able to ping IP address 192.168.29.180 from host-VCP 18 to R5, but unable to ping the gateway of the internet or google DNS.There is no issue with inside and outside FW policy (even I can't be able to ping Google DNS from the firewall as w...
I have configured DHCP services on Server 1 and I'm trying to pull DHCPs on my PCs but it's not working. Any help would be appreciated. Packet File attached. Thanks.
I wan't to ping from "PC" in the right (DIRECTION FES) to PC in the left (DIRECTION KENITRA) but when I ping it fail , I tried to connect "Multilayer Switch3" and "Multilayer Switch0" but I failed , I used the next commands : Multilayer Switch3(conf...
Hi everyone I have a 1921 router with a WAN interface where I see a lot of packet drops. I can see that the drops are throttles and overruns but I does not know how to find the culprit for why it happens. I don't have any CPU issues or anything of th...
Resolved! macsec performance
Good day everyone!I'm investigating the feasibility of adopting MACsec in our network.Given the attached table, created by Cisco (MACSEC and MKA Configuration Guide, Cisco IOS XE 17), could someone elaborate on 'Aggregate Rate Bits' and 'ESP CPU'? I ...
Resolved! Route Tagging and Redistribution Loops
Hello, everyone!If my understanding here is correct, Route Tagging is used to prevent redistribution loops where routes are being redistributed from, for example, Protocol A -> Protocol B -> back to Protocol A. Source: NetworkLessons.com However, I'...
