I am with Aussie Broadband in Australia, and they distribute additional IPs in a somewhat odd way. Aussie Broadband issues the primary address through DHCP, and then the additional IPs you lease are frame-routed via the primary. It's almost like you...
Forum Posts
Hello everybody!In a Lan - Wan - Lan network topology, the following problem is occurring:When I send the PDU from Lan 1 to Lan 2 it fails.From Lan 2 to Lan 1 is successful the second time.How can this problem be solved?
I just want to confirm my knowledge here I guess. In a general perspective, it would seem to me you’d use the inbound statement on a router to only classify/mark because the interface it’s connected to is at line rate coming in; there’s no way to dro...
Hello all,Is it possible to have a route that failover to another ISP2/Connection in the aftertoon from the main ISP1 which is regular. So, I have 2 Towers in same location, both having different ISP. Tower2 is residential and often less busy in the ...
Hello Team,Family.I have attached topology.Is it possible to manipulate routing such that for 192.168.40.0/24 to get to remote side to use r1, and 192.168.50.0/24 to get to remote side to use r2.Assume all interfaces are of same speed.Thank you in ad...
Hello,I'm having a hard time trying to bring up a simple eBGP adjacency between a Nexus 93180YC-EX and a Catalyst 9500. They can't agree on a BGP parameter, to bring up the session. Has anyone experienced this? Forgive me, I can't remember the parame...
Hi, I have a circuit with 5 megs for upload only. This circuit is continuously maxed out and therefor packets get dropped by the ISP.I wanted at the very least to do QOS for voip and control packets such as keep-alives etc.I created HQOS with a paren...
Resolved! several ABR routers
Hello everyone. There is a couple questions about OSPF topology. As it known, ABR routers - routers which connect its area to zero area. For example, 0,1,2 areas, and there is only 1 ABR router on each area, then there is only 2 ABR could bi in this ...
Hello.I just wanted some input on suggestions. My current way works but, and this may not be related, weird things happen. Such as loss of Internet but all is green. All was fine until I implemented my new way so I’m hoping I just missed something.My...
Dear Cisco Community,I am reaching out for assistance with troubleshooting an EBGP (External BGP) configuration issue. I have followed the necessary steps and configured EBGP on all routers, but I am unable to ping the network reachable through the r...
Hi there ,i am trying to do a lab in eve-ng with the following details :i have 2 ISPS also in my LAN i have one route which is connected to the 2 ISPS, i have done the Natting and everything i am just stuck at load balancing and load sharing i cannot...
We have a meshed backbone using ISIS as the IGP with BGP VPNV4 and Route Reflectors on top of that. Given the mesh nature of the network and using ISIS, we see points in the network that have an equal cost path to the next hop of a route. I know ther...
For anyone looking for an answer to this. Google did not help me with this problem, so I will share the solution here. I just installed a IR1821 router at a location, the local ISP delivered fiber directly to the router with a BiDi SFP, GLC-BX-U sing...
HiI'm trying to configue web ui on a isr 4331 router.IOS XE is version is 03.16.06.S, which might be ancientIOS version is 15.5I can connect to webui but the page isn't graphical, just a list of cli commands.Any suggestions.I bouhgt the router to stu...
We apply cyrpto map under port-channel on 2911 router. The new 4431 router also does not allow entering this definition. What is the best method you can suggest to solve this? We do not have control of the other party. Is there a way to run the tunne...
