Hi, How will check our Guest network is not access any company devices and how will make a secure network Thanks,
Hi, How will check our Guest network is not access any company devices and how will make a secure network Thanks,
Greetings, I have a new Cisco 2911 router that I need to install and configure a vwic3 card in. I'm not so concerned about running voice. I will be replacing an existing router into a circuit that will be running a bonded T1. I discovered the link ...
Hi,I am not able to see the EIGRP route in routing table, but the route is in topology table.What could be the issue ?
Hello, I have an 1841 router where interface 0/0 is connected to my DSL connection. 0/1.10 is one of my assisnged public IP's and 0/1.20 is my LAN ip. When I physically connect my internet direct to 0/0 everything works correctly. But when I plug...
We have a shaping policy which is dropping packets when there is a spike in data, even though the spike is no where near close to the shaping limit. An example is the shaping policy limits the outgoing flow on fiber connection to 10000 Kbps. There...
Hi, I have an application (web based), which is connected from the outside by IP (public) only (no DNS, since the connection initiating devices are thermostats and can connect via IP only). I have a static NAT with one public IP only. ASA version 7.2...
Hello All, I have a query on OSPF protocol. My question is if area 0 in ospf network goes down what will be the impact of this on network.
Hello! I have a question about using shaping and policy rules together. Is policy rules works always for prioritization traffic or only when shaping occurs?
Dears, need help in finding out the issue, regarding High CPU Utilization in router 2801. users complain about internet disconnect.
We are seeing a critical and major alerts about a Power Supply Failure and Fan failure but they seem to be fine. Core3rtr#show facility-alarm statusSystem Totals Critical: 2 Major: 3 Minor: 0 Source Severity Description [Index]------ -------- -------...
Hi. We are currently in the process of changing WAN providers. We will move from Provider 1 to Provider 2. I'm looking for some help on how we will configure the Nexus switch in one of the DCs, in order for routes to go via new provider when moved ov...
Hi, I have two devices, a Cisco 1941 router connected to a DL600 E Multiplexer using two cables; a serial to V35 cable and a V35 to DB15F cable. Do I have to switch off the Cisco 1941 and DL600 E Multiplexer devices before replacing the cables? ...
Hi , I have a problem with a Cisco switch catalyst C3750- 48PS-S POE. I want to connect this switch to many UBNT wireless routers.But things go wrong. After stablished connection via ethernet cable nothing happened. Also in switch's CLI the interfac...
Hello, I am trying to setup two IP Blocks on my firewall. I had done two static routes both making them default aswell as the configuration here: https://gyazo.com/c9b79b758fddf76b88a37558a559823e As you can see the route is setup but the routes aren...
Hi, I got the below output using command show ip bgp summary. What is relation between the VRF and bgp? how can we show output of it like normal? Thank you Nexus7K-1# sh ip bgp summary BGP summary information for VRF default, address family IPv4 Uni...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2025 02:39 PM | ||
05-29-2025 10:06 AM | ||
05-28-2025 01:50 AM | ||
05-27-2025 05:13 PM | ||
05-15-2025 07:28 AM |
User | Count |
---|---|
4 | |
3 | |
2 | |
2 | |
2 |