For anyone looking for an answer to this. Google did not help me with this problem, so I will share the solution here. I just installed a IR1821 router at a location, the local ISP delivered fiber directly to the router with a BiDi SFP, GLC-BX-U sing...
Forum Posts
HiI'm trying to configue web ui on a isr 4331 router.IOS XE is version is 03.16.06.S, which might be ancientIOS version is 15.5I can connect to webui but the page isn't graphical, just a list of cli commands.Any suggestions.I bouhgt the router to stu...
We apply cyrpto map under port-channel on 2911 router. The new 4431 router also does not allow entering this definition. What is the best method you can suggest to solve this? We do not have control of the other party. Is there a way to run the tunne...
I'm trying to figure out why my router reflector is only getting 2/3 of the full Internet routing table.the first output here is from the route reflector if you notice it's only accepting "664019 accepted prefixes, 664019 are bestpaths"If you look at...
Hey all,I have a Cisco 2960S-PST-L 48 port switch that will either not forward traffic for one of our VLANs completely or it will forward a very small amount of traffic and then stop. When I connect a laptop directly to the switch, it takes a while ...
Hi Cisco NetPros,i have a short question:We are using several Cisco1841 routers. The show clock command gives the output which i expect (Time = NTP time).But the show log command give the output with a time stamp from UTC (i have to add 1 hour to get...
hello all,Today i am facing an issue with write memory command. i configured the cisco router from console port and no issue to save the configuration.now i am tryin to save the config via ssh port but nothing happened and seems that is freezed . Sy...
HelloInfo:Hardware: ASR-9901-RPVersion: 7.1.3We are an open fibre provider with several white-label ISPs. The problem or rather question we are facing right now is the following.As we only have one border connection to internet at the moment and each...
The Verizon Fiber connection is not offered with a static IP, which is fine, so I've configured the WAN Gig8 interface to use DHCP. I can ping by IP or DNS externally from the router.I'm having trouble configuring the internal interfaces; in my tink...
I have a Cisco 1841 router and the flash card slot has been bent out of place and the CLI is not responding. I am wondering if I am able to buy a new flash port or if there are any manuals that show something similar
Resolved! Cloud Azure Networking
Hello Experts @balaji.bandi @Rob Ingram This may be not the right place but appreciate your support here.I have two Hubs in Azure in two different regions named east and west. East hub has BGP within express route and act as transit for all underly...
Hello everyone.I made a conection of an router Siemens RX1500 on a ASR-920, closing by loopback an eBGP.My gateway (the firewall) with the ip 10.132.30.118 send me a default route. The neighbor of RX1500 (10.255.200.5) receive this default route, but...
Hi, I'd like to consult whether adjusting the route-target under EVPN, which currently doesn't match between DCI and LEAF, to align with each other would impact the services being utilized. I discovered misconfigurations and seeks to rectify them but...
I get the following error when creating or modifying an LTE profile on my cisco router. MidLand#cellular 0/1/0 lte profile create 3 h2g2 noneAccess Point Name (APN) = WF.GW5.VZWENTPUsername =Password =Authentication = NONEProfile 3 already exists wit...
Can anyone please explain why EIGRP choose a route with highest metric. As you can see from the below output, route from 10.18.1.2 has better metric. But it was not choosen Switch# sh ip route 10.1.0.0IP Route Table for VRF "default"'*' denotes best...
