Hello, My company has inherited a job that contains some Cisco stuff that we do not normally deal with. The basic issus is that the ISP has changed and as such, there's a new modem. Internet connectivity is limited, and restoring that is the top ...
Hello, My company has inherited a job that contains some Cisco stuff that we do not normally deal with. The basic issus is that the ISP has changed and as such, there's a new modem. Internet connectivity is limited, and restoring that is the top ...
Hi , "CAB-SMF-LC" item is end of sale, Please let me the replace part code of CAB-SMF-LC item. Thanks in Advnace
Can someone please let me know if I have the correct Source (S) and Desitination (D) defined on the attached diagram, based off the ACL's below and will the attached ACL's work? I was told the ACL will not work this way as the remote site ACL should ...
Hi,I have added Cisco NIM-VAB-A VDSL2/ADSL2+ module in ISR4431 router as backup for DSL line. existing connection is DIA could you please help me, how to configure NIM-VAB-A as backup line if 1st DIA fail ? Regards,I.A
Hi, We have a mail server on which we have two NIC installed one NIC use for public and other one use for private network. On public network int we have given a static IP which is provided by our ISP and its directly connected with a WAN Router. On ...
Hello I have a dual Hub running and i want to activate HSRP. When i change the config the server cannot connect any pc over the VPN of the router. Why? If i deactivate it the router can connect the pc. i think the HSRP cannot connect to the VPN´s f...
I need the BGP speaker's IP, ISP's router with BGP running on it,let us discuss contact me.
Memory usage is short on my A9K-RSP-4G however I just noticed only 2G out of 4G is really available ! Physical Memory: 4096M total (452M available) Application Memory : 3904M (452M available) Image: 62M (bootram: 62M) Reserved: 128M, IOMem: 2028M, f...
Sorry if this is too simple question of a question. Perhaps it's terminology, but I'm unsure whether I have found the correct information. I have a block of IP addresses from my ISP. My router is currently using one of them. Just as an example, let...
Dear Team, We setuped a model as attached file as: PC1 ( Hyperterminal), ASYNC ==> RS232 ==> (Serial 0/1/0/ Router 1) ==> IP ( Router 2, Serial0/1/0) ==> PC2( Hyperterminal), ASYNC. Detail configuration in attached too. After configured i show inter...
Hi Experts!! I could see iBGP to IGP redistribution is not allowed by default to avoid possible looping. We can only able to acheive this after configuring "bgp redistribute-internal" under bgp config. However in MPLS VPN scenario we can use ospf as ...
Dear all, is ASR 1006 supported span port or port mirroring? do anyone have config about that?Thanks.
Hi, I'm trying to configure destination NAT via the NVI on a Cisco router. I have the command 'ip nat source static...' which works fine for source nat; but I don't kow how to do the destination nat, there is no command ip nat destination... any help...
Hello, When i try to add an VLAN to my trunk it results in the following error: switchport trunk allowed vlan add 110 ^% Invalid command at '^' marker. The port is part of a channel group. Is this the problem?
Hi All, Reviewing a client QoS configuration...this policy-map is bound to a 1Gbit interface which neg to 100Mbits, the WAN service is 20Mbits.. policy-map PM-SHAPE-QUEUE-OUT class CM-SHAPE-QUEUE-OUT shape average 20000000 10000000 100000 Forgive m...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 03:27 AM | ||
| 12-03-2025 07:46 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM |
| User | Count |
|---|---|
| 9 | |
| 6 | |
| 4 | |
| 4 | |
| 4 |