Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Resolved! Is it possible to route multiple networks out to multiple public assigned IP addresses on the same subnet and use NAT overload

I have three internal vlans that I would like to each have a dedicated public IP Address using NAT overload. I would like traffic from each internal vlan to use NAT  however all the public IP addresses reside on the same subnet and on a single 10GB p...

psaunders by • Level 1
  • 1213 Views
  • 7 replies
  • 0 Helpful votes

Resolved! I have 300 stores and I'm looking for a global QOS config that would shape/policy the bandwith based on a % of the detected ISP link speed

Hi,We have 300 stores with mostly the same router config.The router in each store is a cisco 891 router capable of doing QOS.Each of our store is connected to internet through a local Internet Service Provider (ISP).  They all have different ISP.Each...

static nat and route-map

Hello guys, I have a problem with a configuration I need to do. I uploaded a sample picture of the network.I want that the server (192.168.1.2) is Nated with the ip 217.X.X.2 (int fast 0/0) and the other equipment in 192.168.1.0/24 nated with the pub...

Kevin SAS by • Level 1
  • 362 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Traffic Not Being Routed Through L3 Switch

Hi all,I have a situation that I'm not sure whats going on.  I have a L3 switch configured with 2 VLANs....5 & 10.  This switch is connected to L2 switch also with VLANs 5 & 10.  I have routing between the VLANs being done on my L3 switch and that se...

Dual ISP - Redundancy and Load Balancing

First off not Cisco certified just self taught in order to keep things running and clean out some garbage from the previous guy. We are adding a 2nd ISP connection this summer and I am looking how to setup our Router to Load Balance while both lines ...

Resolved! dynamic NAT inbound traffic filtering

I have a static NAT mapping from an internal IP to a public IP to allow RDP access to an internal host from the Internet. ip nat inside source static tcp 10.10.10.35 3389 24.90.6.133 5222 route-map RDP_Gateway_Map extendable Works great until I want ...

cisco by • Level 1
  • 1511 Views
  • 3 replies
  • 0 Helpful votes

ipv6 on Cisco 2811

Hi , Cisco Feature navigator says it supports IPv6 on following IOS & Model.System image file is "flash:c2800nm-advsecurityk9-mz.124-15.T7.bin"Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.Buti cannot run "ipv6 unicast-routing" comm...

Resolved! BGP advertisements control

Hello Dears I want to ask about the following case : If I have router in AS 100 with 2 router neighbors ( Assume they are ISPs ) AS 200 & AS 300 and I have networks 192.168.2.0 - 192.168.7.0 I advertise 192.168.2.0 - 192.168.4.0 with one neighbor AS ...

Cisco 2911 stacking.

Dear Team,  We have two CISCO2911/K9 router and need to configure stacking over there, this is the first time am going to do this please share the step-by-step procedure.  Best Regads, Abdul

Resolved! Wildcard Mask -

Hi allVery silly question but stuck in calculating this below wildcard... any help?  20 permit ip 192.168.0.0 0.0.252.255 Just need to know which IP range would it be allowed? Much appreciate for help!

routing protocol over mpls

Hi  all,  i have to implement a network customer over a vpls provider  ( 60 site L2  any to any).which protocol for this design ? eigrp, ospf or bgp with advantage or inconvenient? thanks,     

Load more
View All
Review Cisco Networking for a $25 gift card