I was wondering if anyone has come across this before.I have just started my course in cyber security and the first 2 activities aren't working the same as the videos online show, it seems whenever I use any application within the desktop (web browsi...
Forum Posts
Hi I have the following scenario and little confused about the technology and topology that need to be used RTR1 and RTR2 are the service provider routers (CE), and the provider informed us that they have an active-active connection via BGP.The quest...
Resolved! Type 5 external LSA remove
Hi I've written bad IP address as I redistributed the loopback interfaces into OSPF. I want to remove the IP address from ospf database but the command no network A.B.C.D wildcard mask area X under the router ospf subinterface has no effect. I wa...
Hello,I have a 3825 router with a dead console port. Plus, I can't access to CLI through ethernet port because they admin down after a reset. The router boot and after that, ethernet port are disabled.How can I acces to CLI in this case ?Thanks for y...
Resolved! EIGRP Unequal Load Balance
Hi everyone,hope you can help with EIGRP unequal load balancing in a Catalyst 3650. I have a system where I need to send the traffic to reach the 10.1.40.0/24 via the vlans 4084 and vlan 4087. Due to the metric, the vlan 4084 as the lowest FD and vla...
Hi,I'm unable to ping from the R2 router IP address 172.16.0.1 similarly from the R5 router as well. I configured the OSPF and static route in the R12 router and redistributed it. R12 ROUER interface Ethernet0/0ip address 172.16.1.104 255.255.255.0du...
Hello everyone,Currently, the FPR equipment and C9300 equipment are connected with an optical cable.It was a cable that had been in good use before.One of the FPR2130 devices failed and was restored to its original state.But the problem is that the d...
Dear Engineers, Hello, I am trying to figure out how to apply ipbasek9 license feature permanently.Furthermore, when I run 'show license', I receive the following information for ipbasek9 under Index 4:Router#show lic*Mar 16 06:47:23.752: %SYS-5-CONF...
Dear allin mikrotik same feature name PCQ https://wiki.mikrotik.com/wiki/Manual:Queues_-_PCQ_Examples For exmaple i have DHCP or PPPOE pool with subnet /24and i have 10 client is connected client 1 : 10.10.10.1client 2 : 10.10.10.2client 3: 10.10.1...
We have Cisco 927 routers, C927-4PLTEGB versions, and from time to time we have to install these in locations where the mobile signal strength isn't great - so we are looking at using extension cables. However the 'standard' one is only about 10m lon...
I am getting this error from one of my cisco router:Interface 'Tunnel157-#INCLD-Rajshahi-To-Gulshan-14th-floor#' util threshold violated.Current IN traffic is 11.721 Kbps(11.72%) and OUT traffic is 94.576 Kbps(94.58%), whereas configured threshold is...
actualcurrentdeseabledesirable Hello everyone,I have once conducted an IPSEC IKE version 2 VPN tunnel between two separate networks. Which is a site-to-site. My question is whether an IPSEC IKE version 2 tunnel can be done within a single LAN. I'm no...
Hi,I have 2 environment with in separate rooms with the same subnet 10.10.10.0/24each environment connected to aenv1-switch, this sw connected to cisco asa1(192.168.14.2) connected to myciscoasa(192.168.14.1)env-2switch, this sw connected to cisco as...
Resolved! Spanning Tree
Hello , I have on my switch some interconnection (L2 link point to point) with access port to different provider to receive some multicast all these ports are in vl 200 that is designed for multicast streams. I have a problem because the last L2 li...
I'm working on a Nexus 9000 whose purpose is to redirect traffic to a web content filtering system with ITD. There is an access list that works to match traffic with specific sources and destinations and sets a next hop ip address in the route map w...
