Routing

Resolved! Bgp-Eigrp-Bgp redistribution question

Hi Experts,Just wish to ask if there is an option to retain the as-path information in eigrp when i redistribute from bgp to eigrp then to bgp?I recall coming across something similar to this before but I can't seem to remember it. Thanks in advance....

WAFS Benchmark Tool

Hi, years ago CISCO provided a tool "WAFS Benchmark Tool" for testing CIFS performances over WAN connections. It was free downloadable from CISCO. I am not able to find this tool anywhere in the web. Maybe someone coukd help!Thx, Luce

BGP Router high process

What do we need to do if BGP Router contribute high process in CPU? CPU utilization for five seconds: 97%/43%; one minute: 99%; five minutes: 92% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 44 36270732 35464661 1...

Resolved! Unable to browse the internet after adding ACL to interface.

I have a Cisco 4451-X that I am trying to use a static NAT entry so the internet will see a server on the inside as one IP, but not have an "any" access to the resources on that server. Here are the relevant sections of the config:interface GigabitEt...

Nexus 5548 Dual Home FEX Topology Configuration

Hello Expert,I have 2 Nexus 5548 and 4 Nexus 2248 (FEX FABRIC) and going to install as Dual Home Fex Topology. Kindly See attached Diagram and full configuration script as attachment also. Kindly let me know your expertise about it: Step: 1 Configu...

router that does not route

I was CCNP but for sure a little bit too long to be efficient in routing. We received a new router (CISCO2901/K9) but I’m not able to use it.Very easy scenario : 2 subnet : 1 WAN and 1 LAN. Cisco router configuration :version 15.2no service padservi...

BGP,ZBF,NAT

Recently Implemented with new router.please refer to the diagram and my following questions: 1.2 Routers connected to same ISP with BGP peering and Default route adv to customer router. and both router is not connected each other. 2.Internal interf...

Looking for Cisco 6500 E series 1/10 G SFP Module

I am looking for 24 ports 1/10G SFP module for my 6509E chassis and WS-SUP720-3B sup module.I have found the following from my researchWS-X6704-10GE - 4 port 10G module which supports only 10G not 1GWS-X6708-10G-3C - 8 Port 10G module which supports ...

Resolved! clear ip bgp - Purpose

Hi Friends - Can you explain me when I have to use "clear ip bgp" command to reset the peer relationship with BGP Neighbors.In my understanding iBGP advertise its any route change in 0 seconds and EBGP advertise its route change 30 Seconds. If that i...

Resolved! sho interface <interface_name> history

Can someone explain the "sho interface <interface_name> history" output?

Resolved! 7206 ROMMON ISSUE

Hi there , we got some issues, that tftpdnld and xmodem command is not showing in Rommon mode . -------------------------------------------------------------ReadOnly ROMMON version is:System Bootstrap, Version 12.3(4r)T1, RELEASE SOFTWARE (fc1)TAC S...

Ho w to know the EOL date of cisco router device? Ex. CIsco 3945.

Ho w to know the EOL date of cisco router device? Ex. CIsco 3945.Is it the Last day of support? as stated on the Cisco Site.http://www.cisco.com/c/en/us/products/collateral/routers/3900-series-integrated-services-routers-isr/end_of_life_notice_c51-71...

EIGRP load balancing when using HSRP on LAN

Hi I have a question about my topology. I have two routers with EIGRP on both of them connected through 2 ISPs to other site. On those routers i have HSRP runing. Now my question is: HSRP is standby/active protocol so when one router act as active w...

Resolved! Can you help? Two dialer interfaces with IP SLA for default route failover - issues

I have an issue with a Cisco 2821, it has an ADSL2+ HWIC whose ATM interfaces is linked to dialer 1 and a Gi0/1 interface with a pppoe client which is linked to dialer 2. Both dialer interfaces are up with their respective IP addresses. If the AD...

BGP Multihomed Dual ISP Dual Routers and Dual ASA

I have a client that is requesting redundant internet connections using 2 7204 routers to 2 asa 5520 in an active standby configuration. There is no load balancing requirement this is strictly for failover. The issue that I am having is that I have...