Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

 Basically, I have two routers (Primary/backup) each connected to a different ISP with 100/50 mbps directly connected to L3 MPLS, the backup router is mainly used as a backup router and both routers redistributing routes between bgp/eigrp and vica ve...

I just need to understand this policy map configured on my router. We are upgrading our link and  I might have change the CIR and bandwidth allocation on this policy map. The bps shown here is it bits per second or bytes per second ?   Policy Map VPN...

hi,here is a brief design of our company's topology. I want to know where could i place hsrp in our network since we have backup routers/multilayer switches that are not in use ? Also i am wondering if there are bgp peerings on the routers, how will ...

Resolved! mac acl

Hi , I want to stop traffic from one of my port using Mac acl. I captures frames on wireshark and they are STP and LOOPBACK related. I believe Mac acl is used to stop Non ipv4 traffic which is STP etc.. i am using cisco 2960 mac access-list extended ...

shafi0211 by Level 1
  • 861 Views
  • 2 replies
  • 0 Helpful votes

Resolved! NAT in which IOS

Dear Team,Please let me know if we can do NAT on IP Base Image of any of the following switches or do we need IP Services Image:Cisco 3560-XCisco 3750-XCisco 3650Cisco 3850Regards,Farhan.

Dear Sirs!Approximately once in week, my friends get reload F0 card - ESP-10:Sep 13 00:50:19.676: %CPPHA-3-FAULT: F0: cpp_ha:  CPP:0.0 desc:INFP_INF_SWASSIST_LEAF_INT_INT_EVENT0 det:DRVR(interrupt) class:OTHER sev:FATAL id:2121 cppstate:RUNNING res:U...

Hello, I am trying to understand the difference between cable length 0db and cable length short and how to use them correctly. I don't know what the lengths are that define long vs short. Ex. If I have a router racked up and using T1/E1 card for a T1...

dcanady55 by Level 3
  • 4741 Views
  • 3 replies
  • 0 Helpful votes

Hi Sir, HQ is running Cisco 2621 and remote branch is running Cisco 805. The current CCTV traffic always caused other application like SAP fail to connect to HQ from remote branch. They want to limit CCTV traffic to 1 Mbps only, another 1 Mbps purely...

c.ong by Level 1
  • 779 Views
  • 2 replies
  • 0 Helpful votes

Normally I would be configuring HSRP or VRRP in a campus gateway backup scenario. Layer 2 at the access with VLANs spanning 2 Distributiion switches using HSRP or VRRP.Would I be correct in assuming GLBP in this type of scenario can lead to ineffici...

Location A connects to Location B with two connections One Point to Point T1 One 768KB CIR Frame Circuit Location A has one subnetLocation B has one subnetOSPF is routing protocolCould GLBP be used at both locations to load balance traffic across T1 ...

thomuff by Level 3
  • 934 Views
  • 4 replies
  • 0 Helpful votes

Hi,I have attached a high level design diagram which represents the network topology and multicasting is introduced on the network for camera streams. For multicast using “sparse-dense-mode” and OSPF is used as the routing protocol.Multicast works go...

We have a network in which our core router is at a main facility using a third party MPLS network and routes are populated using BGP. Core Router Cisco 3925 is connected to ISP on Gig0/1 and then to third party MPLS on Gig0/2. I am routing some subne...

Hello. I just want to know how to reduce ospf adjacency time. When broadcast mode, it takes long time to elect DR/BDR when routers are in 2way state. Is there any way to pass quickly this state? Thank you : )

CATYO by Level 1
  • 876 Views
  • 7 replies
  • 0 Helpful votes