I'm currently learning the basics about frame-relay, and everything makes perfect sense so far. There is one thing I just don't get though. Lets say we have three routers going through a frame-relay switch. R1 is connected to two other routers, R2 an...
HelloWe use a Cisco 877 router with a Dialer Interface for Internet and FE Interface for our LAN.A few days ago we discovered that a specific website we access on a regular basis is not reachable from our office. However any network outside our offic...
hi all,i'm currently using a 2811 as our internet/BGP border router with receiving full routes. the current bandwith is 15 meg and planning to upgrade to 30 meg.will the current 2811 handle the bandwith and the full BGP routes at the same time?was th...
Hi All,Bellow is the show version command of CISCO ASR 1000F route:ROM: System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)HOSTNAME uptime is 1 hour, 5 minutesUptime for this control processor is 1 hour, 4 minutesTime since HOSTNAME switch...
I recently bought a 3845 off ebay to replace my 3745on my 3745 I used 3x NME-16ES-1G-p for intervlan routing and had the full ac+inline power setup so I was able to power my AP via POE without a injector (and one NM-1GE for connection to a D3 cable m...
I have configured the G0 interface with an ip address and placed it in the Mgmt-intf VRF. I can ping the management ip address accross my WAN but I cannot SSH to it. I can, however, SSH into any of the transit interfaces.Thank you in advance for an...
I'm wanting to clean up the default class-map. At the moment the key apps are not grouped into a manual class-map & fall under the "default" class.It is concerning that during congestion key apps have to scrap for bandwidth. I'm looking to distinguis...
Hi All,We have on ASR 1002 RP1 router and aaa server. We need to configure BRAS on ASR1002.Can you please guide me how to do it. Please share the related documents.Regards,Satish.
Do Cisco supports BFD on demand mode?If yes, from which IOS and which series. Its critical for some customer deployment.Thanks,Rupak
When we go to term mon information is immediately scrolling even though we have issued the "un all" command. The only way we can get it to stop is to go to config t and do "no logging monitoring debugging". This doesn't happen in our other routers....
I am working at a site that uses IPCelerate (iCast) to page to the Cisco IP phones. We have recently connected a remote site via a point-to-point T1. We have no issues with the Cisco VoIP system or the computers in the newly connected remote site. ...
pls how can i shape on 4500 series switchis it possible
Is there a some sort of OSPF rule that will not allow LSA type 5 link state to cross a non area 0 link between two ABR routers?I have two devices that are in parallel. The site is a tail site off a MPLS leg. The MPLS router is redistributing BGP into...
Hey guys;I have a problem that tired me, and hope to find someone can help!I have Cisco 6509-E with SUP720 which run multihomed BGP and worked very perfectly.I'm running also: OSPF/SNMP/PBR/ACL/Distributed CEFISP1 bandwidth is 2.5 Gbps ( Etherchannel...
Hi All,I'm currently designing the WAN connectivity for a new office. The new office will have dual MPLS connections handed off by two providers, these will terminate on separate 3900 series CE routers, we will have a private BGP AS number.My initial...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-28-2025 01:50 AM | ||
| 05-15-2025 07:28 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM |
| User | Count |
|---|---|
| 6 | |
| 3 | |
| 3 | |
| 2 | |
| 2 |
