Hello all,Thank you for reading. I have a 2811 with an NM-1T3/E3. I know it can't support a full T3 but does anyone know if I can get away with using this on a 15Mb partial DS3? This is just temporary. Cisco only says it supports it "Subrate T3/E3 wi...
Hello..I have a CE router connecting two MPLS circuit both are connected to different ISP with different AS. Both are connected via BGP configi want one circuit to be primary and another one secondary. I am looking to set local preference 50 and as-p...
Hi Team,What is the use of IGP routing protocol in BGP network.Can,t we run only IBGP in our network. If not why.Please clarify.Thanks in advance.Naveen
hi , iam faiz , we have a 15 branches and 1 main branch(hub and spoke) which is running may be bgp over mpls maintained by isp so he provides us router and extra hww interfaces.but now we are going to another isp who doesnot provide t...
Hi,Please let me know the meaning of the below sh ip route output.sh ip route 10.161.5.110Routing entry for 10.161.5.108/30 Known via "connected", distance 0, metric 0 (connected, via interface) Redistributing via bgp 4758 Advertised by bgp 4758 ...
Hi allWe currently have remote sites with an Mpls wan to the hq, each site also has an Internet connection , I need to have automated backup to the Mpls over the Internet. Each site will have 2 routers, for Mpls and for Internet. What's the best way ...
Hi All,I have a router that has a load of static routes. I want to redistribute these routes to another router running EIGRP on the same ethernet segment. I setup an access list etc permitting the routes and the associated route-map. I also know the ...
Noticed that a point to point OC3 circuit has a steady output drops without any other errors or bandwidth issues. thoughts?POS1/0 is up, line protocol is up Hardware is Packet over Sonet Internet address is 10.20.54.1/29 MTU 4470 bytes, BW 1550...
Hi, Does anyone know the new location of http://www.cisco-bt-portal.com/iusr/DSL/Product_Bulletin_DSL.pdf it seems to have moved and I want to check on the latest recommended version of FW for a 1921 running a HWIC-1ADSL.It's currently running AMR-4....
Dudeswe have two routers providing 2 different feeds , if we have one DR, multicast groups on non-dr has not been forwarded to segment.Can we have two pim DR elected on single LAN segment based on multicast groups?, If not pls advice any alternative ...
HI,HOPE THIS HASN'T BEEN COVERED TO MANY TIMES BUT i WAS WONDERING IF anybody had a config that could direct a request to a dhcp server (IPhelper) based on the domain that machine was part of (FQDN).
Can someone help me with setting up a Cisco 3550 Layer 3 Switch to route to Cisco 1841 router.
Something I don't understand. I've read plenty on enable and console passwords and VTY passwords.We have a 1841 router and a 3560 switch that used to be managed by our Voip provider via a dedicated T-1 to their site. We now have an...
I have network performance issue on my net network with routers and switches and unable find the issue ..Need suggestions for resolving issues and how to check in Routers and switches in performance issue ,resolution process ?thanks in advance
Hello everyone!I am facing critical issue for multiple range and destination of port forwarding. I would like to configure NAPT as below. LAN destination addresses WAN address 192.168.0.102 port range 16000 16511 10.0....
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-14-2025 01:24 AM | ||
| 05-15-2025 07:28 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM |
| User | Count |
|---|---|
| 9 | |
| 7 | |
| 3 | |
| 2 | |
| 2 |
