Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Basic Routing problem

Hi.. I have cisco 2911 series router.I am trying to do a simple router set up.My ISP provide me following IP addresses with single physical connection.Primary WAN IP: 58.xx.xxx.6 255.255.255.252  Gateway: 58.xx.xxx.5                                  ...

MPLS Tables

can anybody tell me what is meant by the following terms        NextHopLabel ForwardingEntry (NHLFE)       IncomingLabelMap(ILM)       FEC–To-NHLFEMap(FTN)       Label Information Base(LIB)       Label Forwarding Information Base(LFIB)also, what is t...

SNMP Traps using C#

Hi i would like to do a program using SNMP Traps C#. Example if i plug out a cable from a router or a switch, a prompt will appear in my program showing that "The port has been unplug"Thanks!

bingxunnn by • Level 1
  • 1294 Views
  • 0 replies
  • 0 Helpful votes

So 520 W no Internet connection

Hello everyone I am very new to cisco so please bare with me.  I have a small business and am trying to use my router for about 18 laptops. The problem is I can connect to it with my password and get good strength with 54 mpbs but cannot actually use...

EIGRP Network Advertising

Hi All,Another EIGRP one.On a router, If I only want to turn on EIGRP so an Interface listens for updates do I just use the following command.EIGRP xxxnetwork interfaceIP 0.0.0.0Does this then allow that Interface to form an adjacency and receive upd...

GRANT3779 by • Spotlight
  • 3150 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Problem with Cisco 887VA

Hi I am facing a problem with Cisco 887VA, it has been bought for DMVPN use but as this router has advance Security (router eigrp) command is not support as it was not supported in Cisco 877 so I upgarded Cisco 887VA to (c880data-universalk9-mz.124-2...

Resolved! Partial T3 on a 2811 with NM-1T3/E3

Hello all,Thank you for reading. I have a 2811 with an NM-1T3/E3. I know it can't support a full T3 but does anyone know if I can get away with using this on a 15Mb partial DS3? This is just temporary. Cisco only says it supports it "Subrate T3/E3 wi...

Resolved! BGP--

Hello..I have a CE router connecting two MPLS circuit both are connected to different ISP with different AS. Both are connected via BGP configi want one circuit to be primary and another one secondary. I am looking to set local preference 50 and as-p...

Anukalp S by • Level 1
  • 597 Views
  • 2 replies
  • 0 Helpful votes

about network planing

hi , iam faiz ,                 we have a 15 branches and 1 main branch(hub and spoke) which is running may be bgp over mpls maintained by isp so he provides us router and extra hww interfaces.but now we are going to another isp who doesnot provide t...

Regarding Ip route

Hi,Please let me know the meaning of the below sh ip route output.sh ip route 10.161.5.110Routing entry for 10.161.5.108/30  Known via "connected", distance 0, metric 0 (connected, via interface)  Redistributing via bgp 4758  Advertised by bgp 4758  ...

Resolved! Best way to backup Mpls Over Internet

Hi allWe currently have remote sites with an Mpls wan to the hq, each site also has an Internet connection , I need to have automated backup to the Mpls over the Internet. Each site will have 2 routers, for Mpls and for Internet. What's the best way ...

Load more