Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

ASA5510 - 3560G Layer 3 - Configuration Help

Hi All -  I am currently working on my first ASA5510 configuration and am running into some issues. The ASA is running 8.2(5). The network setup is as follows:Layer 3 switch with 4 VLANs with ip routing enabled.All systems are pointing to the 3560 as...

Terminate Internet Link on an ASA?

Hi all,I need a suggestion on something very basic. There is a requirement for having a Site-to-Site tunnel.Instead of terminating internet connectvity on a cisco router and connecting router to an ASA firewall, can we terminate the internet connecti...

ramkunta by • Level 1
  • 886 Views
  • 1 replies
  • 0 Helpful votes

Resolved! ospfv3 and ospfv2

Hey Folks,I have a doubt.If I run ospfv2 process in one router and ospfv3 in other for address-family ipv4, will it make an adjacency.Regards Thanveer "Everybody is genius. But if you judge a fish by its ability to climb a tree, it will live its whol...

Resolved! New to WANS

Hello,I have two 1841's, setting up a Lab WAN in Packet Tracer. I have one of the 1841's run to a DSL modem, then out to the cloud and the same setup on the other end... from the cloud to the DSL modem and to the 1841 on that end... I have all green ...

ipv6 stateless autoconfig

i want to use ipv6 stateless config to give an ipv6 address to an interface, with a default route towards the server. Is it possible without enabling "ipv6 unicast-routing" on client side.

policy-map question

I have Cisco 2900 routers running IOS 15.1.  I have a pair of routers with a serial interface into an MPLS network (T1)...LAN1 - R1 - MPLSWAN - R2 - LAN2Here is the existing QoS config:interface Serial0/0/0 bandwidth 1536 max-reserved-bandwidth 100 s...

Resolved! Traffic-Shape depreciated?

We recently upgraded our 2811 router with a 2911 router. The 2911 is running IOS 15.1(4)M4. I think that the old router was running 12.4On the old router we used to limit the traffic from a specific host on the LAN to a specific host across the WAN t...

arell1234 by • Level 1
  • 877 Views
  • 3 replies
  • 0 Helpful votes

Cant Access peers on VPDN VPN from LAN

Hi at all!I have a Cisco 876 Router, wich is connected to the internet via a second LTE Router on VLAN2. Routing and NAT works fine there for internet access. No i would like to use VPDN DialUP via pptp to my workplace. The connection is up and runni...

Resolved! Inbound vs Outbound on policy map

I have Cisco 2900 routers running IOS 15.1.  I have a pair of routers with a serial interface into an MPLS network (T1)...LAN1 - R1 - MPLSWAN - R2 - LAN2Here is the existing QoS config:interface Serial0/0/0 bandwidth 1536 max-reserved-bandwidth 100 s...

DSL and interleaving

Hello,Was wondering if someone can help with a problem. I have a customer at a remote location that connects via DSL and they connect to corporate network over an ipsec tunnel. I don't support the line or the cisco router, (only the tunnel) - but wou...

Regarding 12410 router

Hi Team,Please find the below linkhttp://www.spectra.com/pdfs/cisco12000.pdfAnd here it's given 12000 series routers feature set.this portfolio delivers up to 1.28-terabits-per-second switching capacity with wire-speed feature performance, scalabilit...

Resolved! cisco WS-C4507R proxy arp

Hi all,we have a 4507R switch, Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 12.2(25)SG4, RELEASE SOFTWARE (fc1)and we can´t desable proxy arp. we alread tryed the command  (no ip proxy-arp) (no ip local-prox...

View All
Review Cisco Networking for a $25 gift card