This is driving me crazy. IP SLA works for failing over to the secondary connection (from Cable to DSL), however the SLA can never reach 4.2.2.2 from the cable, even when it is up. I can ping the interface from the outside world and get responses, bu...
Hi i have a really simple home network setup using the Cisco 871W 4-Port 10/100 Wireless G Router (CISCO871W-G-A-K9). I can't figure out for the life of me what is going on. Web pages seem to "half load" sometimes (netflix, facebook, bank of america ...
Hi,I have setup a basic PBR config to route Http and Https out of a different interface (fa0/0/0) but for some reason http traffic is still going out of the Gi0/1 interface.Is anyone able to see whats wrong?Config attached minus the crypto stuff and ...
HiI have configured E1 to use PVDm to terminate ISDN connection but I keep on getting the above error message, can you please view my config and see if you can't spot a mistake.Layer 1 and 2 seem to be working fine but layer connection isn't working....
Hi all ,I have a setup in my lab as attached in the drawing.I was expecting to get recursive routing problem - as i used the same static route destination as the destination of the gre tunnel destination,however i did not get any problem and the tun...
Hi,please suggest what are the different ways to inliement WAN Link failover.i have 2 WAN links from different ISP's. Also two 2821 Routers.please suggest.Thanks,Saroj
Hello-quick question. we had one of our links (metro-ethernet) between our main and remote site upgraded from 4mb to 8mb but we still seem to be only getting 4mb. Is there anything else on our end that needs to be done? Thanks for any help.-Marc
Hi everyone,I’d like to ask some failover question. Please help me with it.Thanks in advance.In my network, the network is working well. It can ping 4.2.2.2. In order to test failover,I shut down the interface Gi 1/12 of Core1 switch. After this,From...
Hi,A RFC have been published for the version 2 of the IP SLA protocol and the udp-jitter measure: rfc6812.But I can't find which product or IOS version is compatible with this version of the protocol.All the router I've tested only support v1 (port 1...
I have a 2921 router with dual wan, single lan. I have a single subnet on the lan and two different ISPs with different speeds. I host a few servers internally and would like to have all outbound internet traffic use ISP1 and anything internal, such ...
Hi,I have the following problem.Situation:- one main location M, with ASA5510 (v8.3) which has many (about 100) ipsec tunnels to remote locations. Local subnet is 172.16.254.0/24- some of these remote locations have the same subnet, let's say there a...
Hi,I have a Cisco ASA 5510I am using ASDM 6.1I have a LAN and a DMZ and an internet connection.I am using one of the internet connection IPs to host a HTTP service on a server in my DMZ. (its the same interface as my internet connenction but a diffe...
Hi everybody,I need some of you vlan gurus out there. I want to dumb down a Cisco 886va to act as a pure vdsl bridge modem with a local ip to be able to do some admin work on the router. To some extent my config works, but i think the default vlan 1 ...
Hi!Apologies this is a very newbie type question!In our office we currently hace a CISCO 861 Integrated Services Router. However we are about to change service provider and as a result will require dot1q encapsulation, and it appears that the 861 do...
I will be installing two 2811 routers with four dedicated (point-to-point) T1 connections.Is it better (faster) to use Multilink PPP, IP CEF, or can I use a combination of both?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 04-27-2025 11:23 PM | ||
| 04-22-2025 02:16 PM | ||
| 04-22-2025 12:20 PM | ||
| 04-16-2025 08:28 AM | ||
| 04-15-2025 06:30 AM |
| User | Count |
|---|---|
| 6 | |
| 5 | |
| 3 | |
| 2 | |
| 1 |
