Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Resolved! T-1 clock source

Hi,I'm going to be replacing a few 1760's with new 1921's. There's a main site and two branches. The original configs puzzle me because I assume both T-1's at the main site are the same provider, but one is clock sourced internal and the other isn't....

lcaruso by Level 6
  • 1373 Views
  • 5 replies
  • 0 Helpful votes

Hello folks,Does anyone know how I can configure the Aironet 3600e by Cisco without a WAN Controller. I know it's a controller based AP but I bought it in preparation for my new WiFi Network Design as I'm planning to deploy these APs together with a ...

BigBee117 by Level 1
  • 1911 Views
  • 4 replies
  • 0 Helpful votes

Hi I have 2 sites, they are connected via an MPLS service.I have a statement on both of them that creates a vpn tunnel using cryptomaps, the peer address is the providers MPLS address of the router for each site.my question is, when I do the match ad...

Buena dia, Amigos!I have a short-term overload CPU from time to time.It doesn't worry me, but I cannot access to router in this time by Telnet or SSH.Can anybody give me advice on how I can prioritize the manage traffic on the CPU.Hasta la vista, Ami...

Resolved! 1721: IOS Bug?

Hi-Just a newbie - hope I am posting in the correct forum/discussion area - if not, please tell me or direct me.We have a 1721 here in our server room.Our IOS version: 12.3.11(T10) --> c1700-k9o3sy7-mz.123-11.T10.bin We have been experiencing issues ...

HiI’m testing a 1841 with 2 WIC-1ADSL cards, but the connections are dropping every 30-50mins. If I swap the cars out for HWIC-1ADSL’s then the lines are stable. I’ve had the profiles on the lines dropped the 4mb down and 512k up but I’m still gettin...

brasso_42 by Level 1
  • 1330 Views
  • 2 replies
  • 0 Helpful votes

Hi guys,First time herei am having trouble with the point to point tunnel that i configured on the two routersWhen i do sh ip int brief, tunnel on the both routers is whowing up but i am not able to ping the destination ip adddresses on the both rout...

Hello,I'm using PA-SON-OC3 on 7200VXR (NPE-G1). I want to upgrade the link to OC12 with same wavelenght. I found PA-SRP-OC12SMI for this purpose but I'm not sure about compatiblity. Please leave your comments on this topic.

when we transfer  the data from site 1 to site 2site1--172.x.x.98site2--172.x.x.100As two links are there in etherchannel and both sides are src-dst ip based loadbalance.So when i transfer the data from site 1 it will choose link 0 right ? from site1...

Resolved! VRF, BGP and OSPF

Hi, I hope someone can help me or point me in the right direction for a possible solution here. I'm currently working on a solution to terminate a new MPLS network. The connection is VRF within BGP. There are two VRF's coming in via BGP. These two ne...

kegodfrey by Level 1
  • 4297 Views
  • 5 replies
  • 0 Helpful votes

I have an issue where 2 WAN routers have 1Gig links to the Internet by default and are participating in Eigrp. One interface is set to auto (1G) and the other is set for 1MB BW. The previous group supporting this did the config this way, and I'm thin...

Hi Frnd,Pls help me regarding below output --volkswagen_aurangabad2_in_mpls#sh int s0/0/1:0Serial0/0/1:0 is up, line protocol is up  Hardware is GT96K Serial  Description: * Connected to PE4-PNQ-AP Serial4/0/18:0 *  MTU 1500 bytes, BW 1984 Kbit, DLY ...