I'm just double checking here because I saw one doc that didn't mention the 2900 on the data sheet but, I ve seen the 2900 listed with on others. I don't see the 2900s listed in this with the interface.http://www.cisco.com/en/US/prod/collateral/route...
hi all,sorry my BGP is now a bit rusty. i would like to know if the network 203.A.B.0 for the show ip bgp neighbor commandoutput is a /24. also, could someone enlighten me on the /21 le 24 for the show ip prefix-list command and if we can write direc...
Hi,In a DMVPN implementation, I want to be able to create a report showing remote user bandwidth consumption of the headend interface by user's tunnel interface. In addition to configuring netflow on the headend, do I need to configure netflow on the...
Hi I was hoping someone could take a look at my current config and help me get this router into production. I have two WANs one primary ADSL2+ and seconday SHDSL. 1. I want traffic to failback to secondary if primary fails.2. I want https traffic des...
I have a router (R6) that sits on the border of area 0 and area 6. I wish R6 to advertise a default route into area 6 using the area command.This exercise is being done in GNS3 and is for study purposes.When I type the command I get the following out...
Hello, as a Cisco newbie I am thinking about building a linux router (for a study project) to connect to a Cisco network (2 x 1841 routers).Can somone please tell me what kind (standard) of serial interface card will I need to install on the Linux PC...
Hi Guyshow can i verify a particular ip address how much bandwidth he consumes(download for the internet) in order to police this traffic thanksjamil
HiThat equipment CiscoASR1002 with performance 10G I can use. A customer requires 10G in performance.Thanks
I'm needing to know what is the best way to test and verify connectivity on a xconnect when one side is a ASR9k?Normally if I need to verify connection across my network I pin up test IP's on the handoff vlan on both sides and ping acrossExample:Both...
HiI have an ipsec GRE tunnel between two data center with 200mbps dedicated bw. As such it works fine but when doing sustained data transfer even at 512 Kbps, GRE tunnel goes down. Any ideas?ThanksNareshSent from Cisco Technical Support iPhone App
Recently, I purchased a Cisco 871W Router with which to practice/study for my CCENT with. Since I have made the purchase, it has given me nothing but headaches.I cannot access the router to configure it, as the previous owner has a password set on it...
On the Cisco forums, an example is shown for how to configure BVI and bridge-groups on an ASR1004 but the same command (bridge-group) is not available under the interface on our ASR routers. Can someone tell us why? We are running version of code...
Hi,I implement a basic split DNS in my router : a default view wiht my parameters (forwarding source interface...). What I need to do is have another view which will be applied only when computers in the network will try to access *.mydomain.com (for...
Hi,I have a SP that is requesting the following and I wanted to see if I can get your feedback.Customer requested a 2 circuit T1 with Internet, as a new requirement the custemer requested to configure tunnels for INTRANET communication and the recom...
I have a 6509 with 100's of vlans on it, but in this case I am only concerned about 4My default vlan isVLAN 110.168.100.0 /23 with the 6509 interface ip address of 10.168.100.1VLAN 1010.168.110.0 /24 with the 6509 interface ip address of 10.168.110.1...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-03-2025 07:46 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM | ||
| 10-26-2025 02:24 AM |
| User | Count |
|---|---|
| 10 | |
| 6 | |
| 5 | |
| 4 | |
| 4 |
