Hi!I set up Cisco NAT and it works weird...Ping through NAT works, but ports are not available, although the broadcast is on: ip nat translation: tcp xx.xx.xx.55:56666 10.10.0.25:56666 172.16.0.100:888 172.16.0.100:888icmp xx.xx.xx.55:35 10.10.0.25...
Hello.On an ASA 5525 there is a site to site tunnel...L2L local int = g0/0 . outside , L2L local public IP address = 1.1.1.1 L2L remote public IP address = 2.2.2.2L2L remote server = 172.16.1.1---What is my EIGRP configuration to advertise the remot...
Hi,I am unable to ping domain names like google.com. I can however ping 142.251.46.174.Here is my config. version 15.7 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boo...
Hi everyone,i'm using router 4431 with config port access with isp to connect internet. but when configuring port-chanel on router with 2 port access, ping dropped packet, I have tested shutting down 1 of 2 ports but the result is still the same. the...
Hi, I want to change a L2 port on a Cisco C1111-8P to L3 routed port. I am unable to accomplish this task with the no switch port command which worked on other C800 series routers. Can someone help. Thanks
Good day everyone !I'm Linux Engineer for a large organization.I have some good knowledge of Cisco, also SNMP, DB, programming...I'm building an Open Source solution (Running on SuSE Linux Enterprise Server - SLES) to have an inventory / CMDB of all ...
Hi,"In the diagram above, there are two core switches with a Layer 3 connection between them. Between the firewall and the core switches, there are two switches. There are Layer 3 connections between the switches and the core, along with an additiona...
Not sure what to get. I have an Arris Cable Modem that does up to 2.5g. yes I know what i'm asking for is overkill. Yes I know its noisy, yes I know they get hot. I don't care. I don't care what your opinion is about them, I don't care. I don't care!...
how can i verify if a cisco HWIC-4T serial card type is V1, V2 or V3?
Hello all,I'm trying to figure this out for more than a hour without any breakthroughs. I have a cisco catalyst 6880 switch which acts as MDF core and an IDF hanging off it in a port channel.my question is , if i apply a QoS policy on the access port...
own1 and own2 are configured with static routes 'ip route 192.29.8.1 255.255.255.0 192.168.11.254. which are redistributed into OSPF., where eon2, eon1, own1 and own2 are running OSPF in area 0. I will need to be able to ping from FW1 sourcing from i...
HI router interface is shutdown, why do I see a static route in the routing table? Does the flow control command affect it?
Hello,in a production environment, my desiderata is set up 2 bgp instances on 2 different vrf to 2 different eBGP provider. This is not possible for the existance of one router bgp confgiuration already enable. Topology is a redundant NxK with 1 N7k ...
I currently studying my CCNP SP thought CBT nuggets using EVE-NG, however I am up to doing VPLS. My current CSR1000v only has ipbase and security which doesn't allow me to configure l2vpn config. Is there anyway I can get an evaluation license or csr...
Hello guys! I urgently need your help!We are the local ISP. One from our city cores is Cisco 6509E.Core.KamPod.C6509E#show versionCisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9-M), Version 15.1(2)SY16, RELEASE SOFTWARE (fc2)Technic...
