Buy or Renew
Buy or Renew
NOTICE: You can now engage in the community. Learn about the great new Cisco Umbrella content.

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

MFR link not coming up

Hi I have two frame-relay link configured as MFR on cisco 2821 with IOS c2800nm-advipservicesk9-mz.124-19.bin.On CE end its showig UP/Down but at PE end its showing down/down, Searched cisco site but found only one document but even could help me out...

praschau by • Level 1
  • 3270 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Static NAT help

I need to permit the conexion from outside to inside in a 2911 Cisco router, only from an Public IP Address (supose 1.1.1.1) to some local private IPs.I have one question: Using the command: ip nat inside source static tcp <local ip> <port> <global i...

Resolved! Cisco 2801 security issue - open ports

Hello all,I have some strange issue with my cisco 2801: The router has 2 interfaces with legal PA addresses - one to ISP and one to my LAN.There is no nat configuration on this router.When I run nmap scanning on IP address that configured on LAN inte...

PPPoE Server with DHCP

I am helping my customer to test the PPPoE solution. The requirement is that she like to have a PPPoE server (7200), enable the DHCP pool on the router. The PPPoE client (1811) should receive the IP address through the DHCP and with subnet mask (/24)...

v.chow by • Level 1
  • 4287 Views
  • 2 replies
  • 0 Helpful votes

Resolved! QOS on Etherchannel in Cisco 3560

Hi,I am trying to see how can configure MQC in Etherchannel. I know that i need to do this in the memeber physical interfaces of the etherchannel.The etherchannel is a trunk port allowing few VLANs. SVIs are created in the switch for this VLANs as we...

anilrs3 by • Level 1
  • 1614 Views
  • 5 replies
  • 0 Helpful votes

no frame on e1 controller

we are configuring a ras on 3925 router with e1 controller. when we connect the e1  controller  to pbx we got on pbx a no frame alarm (detailed error is that we have nfas but we do not have cas). what could be the error? do the router need dsp to hav...

claudiols by • Level 1
  • 457 Views
  • 1 replies
  • 0 Helpful votes

Resolved! OSPF Hello

Hello, OSPF HelloI have a simple network in GNS3 with 2 routers connected by a Frame-Relay switch. On router 1, the serial interface is configured as ospf network type broadcast, and I have static dlci mapping, broadcast keyword included.On router 2,...

Resolved! BGP and ASN assignments

I am currently working on a project that involves multihoming a 10Mbps Metro-E /24 with a 100Mbps Metro-E /27 from two different ISPs. I need to get BGP info from the ISP own the /27 however, they tell me that ARIN requires a /24 in order to assign a...

TheZman78 by • Level 1
  • 1037 Views
  • 3 replies
  • 0 Helpful votes

1811 config differences

I am setting up my 2nd 1811 router for NAT and VPN.  The 1st 1811 works great, completed a few months ago.  On this 2nd 1811, I decided to just copy the working startup-config from the good, 1st router to this 2nd, and then change IPs and from there....

umbernaut by • Level 1
  • 2470 Views
  • 10 replies
  • 0 Helpful votes

WAN failover over 4G wireless

I am currently working on a project to bring up a 4G\3G secondary connection (failover) in case the main MPLS link fails. The set up is something like that: The goal is to make sure the 4G kicks in when the main mpls ckt goes downI have tried by puti...

Resolved! Cisco WAN LAB

I have two Cisco routers with two integrated T1 CSU/DSU. I would like to connect them between each other to simulate a WAN but not sure how. I have used a cross over cable with special pin out for internal CSU/DSU but that does not seem to work. If s...

juan-ruiz by • Level 1
  • 597 Views
  • 1 replies
  • 0 Helpful votes

How is bandwidth reserved in a LLQ?

Hi,I'm wondering how bandwidth can be "reserved" in a LLQ. For example, say I build the following policy map that puts voice traffic in a LLQ and also reserves 20% of a circuit's bandwidth:policy-map QUEUE_SERVICE_EGRESS class VOICE_EF priority perc...

pweinhold by • Level 1
  • 513 Views
  • 1 replies
  • 0 Helpful votes

Resolved! o2 dsl - 1483 bridge

Hi, I am having trouble connecting my 887 to my o2 broadband service.  Here is my configuration - sh runBuilding configuration...Current configuration : 1684 bytes!! Last configuration change at 21:36:59 UTC Tue Jan 17 2012! NVRAM config last updated...

View All
Review Cisco Networking for a $25 gift card