Hello all I have a number of Cisco ASR920 Routers (ASR-920-12CZ-D) that need upgrading from XE 16.9.3 to XE 16.9.7 (16.9.7 is the customer request) I have downloaded the .BIN file from Cisco and followed the below process: Router#copy usb0:asr920-uni...
Forum Posts
Dear all, I have a following topology in my lab: R1 (as 208097) -- > R2 ISP (as16010) -- R3 (as 35805) | R4 (as 10101) I want to prepend my announce for AS35805 only...
Resolved! install mode on c1111-4P
Hi, is it wise to use the install mode on cisco 1111-4p like we do on switches? We used to do it with bin file, i tried it with install mode using package.conf to boot off and that works. Is this the recommended way now for all cisco devices that run...
Resolved! EIGRP - advertising subnet
I have got switch A connected to switch B and switch B connected to switch C. There is EIGRP between switch B and switch A. Switch C has got a loopback with IP -10.252.5.112Switch A interface Vlan99ip address 10.252.5.1 255.255.255.192endrouter eigrp...
Hi allHope you'll be able to helpWe have 2 core switches and 2 access switches and 1 firewallTopologyThe core switches have HSRP Configured on all vlans where core 1 is is active for 2,3,4,5,6 and core 2 is active for vlan 90,21,100.the vlans are als...
EDIT:To the new people who see this post here are the updates.I need some help with my topology. I have 3 LANs in Australia (CBR, SYD, and MELB) and 2 international LANs (NY, and LDN). Each network has 3 VLANs, one for Native, one for Admin, and one ...
Hello,I am running into an issue with my 2911 router. When I power on the router all 4 fans spin up, shortly after turning it on fans 1 and 2 will stop spinning and a few seconds later fan 3 will go to 100%. The two fans don't seem to spin back up. D...
I have a failing ISR4351 and my RMA is on the way. I’ve never replace one of these before. Any instructions and tips out there?
I have 3 ASR 1001-X. I have upgraded all of them from IOS-XE 3 to IOS-XE 17 (along upgrading ROMMON TO 17.3.1). The problem isو just one of them is working properly now and two others are not. For example sub interface is not working but physical int...
In the ensari CG page 100:EIGRP supports unequal-cost load balancing, which allows installation of both successorroutes and feasible successors into the EIGRP RIB. To use unequal-cost load balancing withEIGRP, change EIGRP’s variance multiplier. The ...
Resolved! RV340 & WISP WAN Connection Problems
Hello. We recently purchased an RV345 to use in our SMB setting. We have a static IP, gateway, subnet, and DNS1 & DNS2 from our WISP, and the configuration is very simple - something I've setup many, many times in the past. There is no MAC lock on ...
Hello everyone. I'm trying to setup a lab to experiment FHRP technology on DMVPN. As depicted on the picture above, we have two DMVPN hubs and three spokes. Both the hubs are configured as NHS on all three spokes. The DMVPN phase 3 has been implement...
Could you please give me the simplest configuration to shape all outgoing traffic in cisco iou GNS3 to 20 mpbs ?
Hi. I would like to try to insert a RV320 into my existing network (for IPsec client VPN purposes), right behind an RV134 (it only does PPTP or site to site), without disrupting the port forwarding, DMZ and an IPIP tunnel to the current nw. I am atta...
Resolved! BGP not forming sessions
Doing a lab. R9 is not forming sessions with R10 and R11: here is debug on R9 Jun 8 23:00:58.002: BGP: 192.10.10.10 Active open failed - tcb is not available, open active delayed 10240ms (35000ms max, 60% jitter)*Jun 8 23:00:58.002: BGP: ses global 1...
