Hello everyone, I am trying to configure my switch so everyone who has an account on my AD can log in using ISE authentification server and here is the configuration in one switch:SW-IDF-1F-B#sh conf Using 13014 out of 2097152 bytes ! ! Last configur...
Forum Posts
Hi, We are getting DDR4 init/training failed in Catalyst 9200L-24P-4G Switch while booting. Please suggest. Snap attached.
hello im a student..im stuck at when i want to ping PC A to web server it show "Destination host unreachable"how to solve it? https://drive.google.com/drive/folders/1rzNIt5gySof-Ym_2wehE-uxTkrEc9Mwy?usp=sharing -this is my packet tracerthank you
Hi All, Kindly support to clarify about MLA behavior.- How the MLA behavior will get impacted/changed where there is two ISIS event with 5 sec i.e. default rib-update-delay timer 5 sec. Will it get cancelled or another MLA tunnel will be formed ?- Wi...
Resolved! ASR-920-4SZ Port Speed
Hello, We have a ASR-920-4SZ router hat connects to our ISP. This Internet link is set at 100Mbps. We requested our ISP to upgrade the circuit to 500Mb. On our ASR, the speed on the Gig port that connects to this circuit is set at 100Mbp. I wanted t...
Can any one suggest me that the license is an evaluation or original in the router.Output is shown below:sh licen allLicense Store: Primary License StorageStoreIndex: 0 Feature: datak9 Version: 1.0License Type: PermanentLi...
Resolved! ASA 5525 - High Memory Utilization
Hello,Our ASA 5525 (IOS 9.14.4.24) is experiencing high memory utilization. This is what I see so far:fw1# show memoryFree memory: 815972661 bytes (18%)Used memory: 3575802776 bytes (82%)------------- ------------------Total memory: 4391775437 b...
Anyone have a solution to IOS downloads failing from the Cisco Software Downloads page? Just keeps failing and saying to contact customer support, then my customer support inquiry fails to get submitted.
Resolved! NHRP NETWORK-ID in DMVPN
Hi everybody, I hope you all are doing fine. I have a question on NHRP network ID. This is what Cisco Doc says: http://www.cisco.com/c/en/us/td/docs/ios/12_4/ip_addr/configuration/guide/hadnhrp.html The NHRP network ID is used to define the NHRP d...
Hi All, currently we have ISR4k router with 400 mbps internet circuit which connected to 1 gig port. we are planning to upgrade the internet circuit to 1 gig, do we need to upgrade port capacity also or not required?
Hi People, I have an issue with my ISR4221/K9 that I am setting up for the Cisco console terminal server. Here is my config: hostname HOBART-CONSOLE!boot-start-markerboot-end-marker!!no logging consoleaaa new-model!!aaa authentication login consol...
Hello, I am working on a assignment for one of my classes where I am tasked with building a network consisting of 4 AS' and BGP routing for communication throughout. We have been able to build the entire topology, but the subnet between R6 and R5 is ...
Hi everyone,I’m trying to set up my Cisco C1111-4PLTE (running IOS XE 17.12.4) as the main router for my home network.My Goal:Use Cellular0/2/0 (LTE) as the primary WAN connection.Use the 4 LAN ports (GigabitEthernet0/1/0 to 0/1/3) to serve home devi...
Hi,At the VMware Workstation 17 player Virtual Machine Network Adapter settings, wether I used Bridged Mode or NAT Mode, the Cisco Modelling Lab 2.6.1+Build 11 is not displaying the ip address to access the CML User Interface. Please kindly help me o...
Hi, Ihave isp connection DIA100mbps. i am isolation this connection in 60mb & 40mb. I am using 2921 w/o sec for main connection 0/0, 0/2 40mbps to tplink switch SG2428 0/1 60mbps through point to point power beam 5ac to router 2 2921. 0/1 s1 cbs250 ...
