Routing

Hi, We have two sites in our company (main and branch offices). Both sites have two ADSL connections to internet. Both sites have a Cisco 2911 router with two HWIC interfaces each. I would like to know if the following scenario is possible. We would ...

DearsI have problem with a particular subnet. It is not able to access a server port from this particular subnet only.Other public IP subnet can access without any problem. The server port is 829. I checked the firewall configuration, nothing is bloc...

Hello, Any one got experience with Cisco 3620 routers doing automatic updates of ip addresses with zoneedit? I hav a non-static ip address and want the router to do an update when the ipaddress on the interface changes. Any help would be much appreci...

I'm setting up a 871 routerand my final config is not allowing client SFTP connections from the Internet. I think it has something to do with the way CBAC is configured. Don't totally understand how CBAC works, but wondering If I should ditch CBAC al...

Dears,I have a 7206 VXR NPE-G2 running in an ISP at 40% CPU in peak time.I applied NAT with overload based on the ACL below. After that, CPU started to reached 90 % in peak time.  Is that expected or I am missing something ?Extended IP access list MA...

the title above, how and what command i should type to set http server ip address inside cisco 877w in order to meet requirement for cisco configuration professional 2.3. what type of physical port i can use after setting http server ip address insid...

Hi,I would like to grab more info on: How do we apply Etherchannel on multiple link between 2 device? Is etherchannel feasible on layer 2 and 3 device?Thanks so much

Hi,I have an ASA 5505 w/ Security Plus.I have a block of 5 consecutive IP addresses from my ISP.I want to put 5 sets of services, located within a single dmz, port-forwarded to specific external IP addresses (eg, mail.mybiz.us, www.mybiz.us, etc).I c...

Dear All, /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-paddi...

Hi to all,I'm working on a simple implementation of VRF and gre tunnel to archive this topology :                     Ce1                      |ce11----f1/0-MLS1-f0/0----f0/0-R1-f0/1----f0/1-R2-f0/0----f0/0-MLS2-f1/0----ce21                     |    ...

Hello, I have purchased a /27 WAN IP,and i constructed a tunnel with one of the IP other than the gateway IP.Theoretically the tunnel should work with out Route, but now in my case it is not working.I Wanna to route all tunnel (IPSec) traffic to the ...

Dear all,help me for  route or switching issueI have 7609 Router( Loopback- 10.99.0.174) which is connected to 2 Me3400 ( l2 Switch) like below10.96.16.36=========>10.96.18.100=========>10.96.16.517609.Interface.ip     MES01--Vlan.Ip         MES02--V...

Dear All,Kindly Update me the Practical Bandwidth Supported on WIC 2AS card on 1841 router, as per techical specifications its supports a maximum of 128 Kps.Or is it dependent on the back plane speed of the rotuer????Regards,Ranjit Shinde

Hi All,I tried configuring policy-map in a fastethernet 0/1 switchport on a cisco 2960 switch. But the configuration doesn't take effect. Once i move the policy-map to the interface vlan it's giving me an error that policy-map cannot be configured on...