hi,internet is very slow in cisco 3600 router.i changed some other higher end ios in my cisco router but the same problem continuing.i have attached my running configs.
hi,internet is very slow in cisco 3600 router.i changed some other higher end ios in my cisco router but the same problem continuing.i have attached my running configs.
Hi,Our Service provider cannot provide one pipe of 6MB, so we got two pipe of each 3MB. Both links with Ethernet interface.Our requirement is to connect GRE Tunnel to our consultant-corporate network.Autocad file would be transferred on this link so ...
whats the diff btw "logging monitor" and "terminal monitor".
Hi Experts,I am doing the below scenario in a Lab environment and now I expect your help in understanding the Framerelay behaviour with OSPFI have Cisco Router HUB,SPOKE-1,SPOKE-2 connected each other in a Fram relay cloud. HUB router is configured a...
Dears,The problem is i have a static ip on router interface and it is configured for pating.But i can't ssh to the public ip address unless i remove the IP nat outside on the wan interface.Is there a solution to this issue?
Is it possible to use a Cisco ACE10-6500-K9 on a Cisco 7609-S with route processor RSP720-3CXL-GE (c7600rsp72043-advipservicesk9-mz.122-33.SRB2.bin and 7600-PFC3CXL)? If yes, what other cards are required?
I have a router on the network, and I use some tools (like whats up) to discover it, without configuring the snmp host XXXX, and other snmp parameters on the router. How come the software detect the router without snmp config on the router?? Whats is...
Hi ,When I try to access my console port(3640 Router with 1 module with 2 ethernet card ) I am not able to access the IOS or type any command .I am getting the following unredeable message.šù¤ üù°þèËþè° þþÃîçúþÃù þøáþþTÃ...
Suppose I have the following scenario:Rip distributed into OSPF area 2,which connects to OSPF area 0OSPF area 3 an NSSA area also connects to area 0Would the distributed RIP routes from area 2 be seen in area 1?Since the RIP routes would be seen as E...
Hi Experts,This is in reference to ZBFW and NBAR URL Filtering What is the difference between Header field inspection and URL inspection in Zone based Firewall. After reading the Cisco documents I learned that, URL inspection is used as below:paramet...
I have a L3 cisco 4506 (LAN) and a cisco 3845 (WAN). Im running a single area OSPF network. Would you use the network statement to advertise all your L3 interfaces on the 4506. Or use redistribute connected subnets and the network statement on the...
Dear allMy cpu is 94% on cisco 2811I want stop one of my PID but I dont know ow can I stop a process with IOS commnads?please help
dear all,pls suggest for following pointssorry for attching jpg file because it difficult to draw topology in notepadissuei am getting all the vpnv4 routes on all PEs, i am able to ping vrf IP of another PE but i am not able to ping client end MPLS ...
Hi we are using the two 4948 switch with two different IOS existing one is cat4000-i9k91s-mz.122-25.EWA14.binbut for OSPF and BGP we upgraded the IOS to cat4500-entservicesk9-mz.122-31.SG3.binnow what is my worry is for two IOS ther is some different...
Hello,I was doing some sniffing of phone and switch packets being send using various vlan option (vvid, untagged, none, dot1p). Looking at the CDP exchanged I noticed that when using the untagged option (switchport voice vlan untagged) the switch sen...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-20-2024 04:56 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM |
User | Count |
---|---|
16 | |
12 | |
6 | |
4 | |
3 |