Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I learned from Cisco CCNA that a directly connected static route specified with an exit-interface has an administrative distance of 0. That seems very promising, because next-hop routes have an AD of 1. I tried to work with these kind of routes in Pa...

keesepema by Level 1
  • 3079 Views
  • 6 replies
  • 0 Helpful votes

Recently, when I log into my switches (SG350X-48), the webpage is super slow to load.  it shows "processing data 60%".   then sometimes it stops. sometimes it doesn't finish.  sometimes it does load but the graphics (links to pictures) are missing. I...

SCOTT No2 by Level 1
  • 2885 Views
  • 3 replies
  • 0 Helpful votes

Hello,I have some questions about this routers series.I understand this series is for SD WAN router, i am right  ?The router factory configuration is with and vedge IOS.By default all the interfaces are linked to the VPN0, is it possible to use this ...

Resolved! ACL

I'm a total newbie so sorry this   I'm using Cisco Packet Tracer I'm simply trying to stop ICMP ping from a PC (192.168.3.4) to the Router 2811 (192.168.4.1) access-list 101 deny icmp 192.168.4.3 0.0.0.0  I get Incomplete  access-list 101 deny icmp 1...

muos by Level 1
  • 2305 Views
  • 12 replies
  • 0 Helpful votes

Hello guys,I'm working on a project, here's the picture Circle in the middle has MPLS configured, I've configured VRF's and managed to ping 3 sites Split, Makarska and Imotski. Next step I added internet router and configured static routes so each si...

Mirko442_0-1673889721723.png Mirko442_1-1673890031328.png
Mirko442 by Level 1
  • 2052 Views
  • 8 replies
  • 0 Helpful votes

Hi  Im from Canada my internet connection is with bell . I have pppoe credentials for internet  Bell use 0/35 for internet and 0/36 for video My pppeo work great but i need help for setup my video 0/36   ... this address is received by dhcp from isp ...

Ando1234 by Level 1
  • 687 Views
  • 4 replies
  • 0 Helpful votes

Hello,I have a very low speed between two routers using L2TPv3 XCONNECT...One of the router is in PPPoE :interface Dialer1encapsulation pppppp authentication chapip mtu 1492ip tcp adjust-mss 1452How to calculate the correct MTU value to use in the PW...

sebastien3 by Level 4
  • 2294 Views
  • 11 replies
  • 5 Helpful votes

HelloThanks for your time to help.I am learning EIGRP. May I have your help?In Reliable Transport protocol (RTP), after device send packet to 224.0.0.10, it will wait a time call multicast flow timer. This default is 50, unit is second.If not receive...

gdy1039_0-1673782344204.png gdy1039_1-1673683264234.png gdy1039_2-1673683277711.png gdy1039_0-1673875697205.png
gdy1039 by Level 1
  • 845 Views
  • 4 replies
  • 5 Helpful votes

Hey guys Today I wanted to work from home in and I installed the VPN Service according to the instructions they gave me. We use the Cisco Anyconnect service. But it always shows me the error "could not connect to server. Please verify internet conne...

helmut89 by Level 1
  • 718 Views
  • 2 replies
  • 0 Helpful votes

I have my CCNA but I have 2 4451 routers that use dial peers and run iOS-xe. I know there are classes on working in the Nexus NX-OS. Is there such a thing for the 4451? The command structures and things like dial peers seems far enough removed from n...

sheni45 by Level 1
  • 464 Views
  • 1 replies
  • 0 Helpful votes

HiI'm working on a very simple lab with two BGP routers in the same AS. But for some reason I cannot advertise any prefix to either routers. I know this may be a very simple error... Thank you. Router1 interface GigabitEthernet0/2ip address 192.168.1...

Aoi by Level 1
  • 1078 Views
  • 5 replies
  • 0 Helpful votes

We have a number of RV042 units deployed in the field and several of them are rebooting every minute or so.  It started a few days ago.  There was a thread about this issue that I was watching but it's suddenly not accessible anymore.Could someone le...