Hi i think i may have accidentlly issues the wrong factory reset command on this router and now the licenses dont look right. I issued factory reset all and I think it removed the licenses. Here is what the show license command comes up with:outer#...
Forum Posts
Resolved! ISR Hardware Throughput
HI.As we know for ISR4000 series there are hardware throughput level, if my hardware license now is 100Mbps this mean 100Mbps for all port or for each port?
HiI have a general question, what would be the reasons of ditributing customer routes (xDSL customers for example) into a service provider IGP backbone ? why don't just use BGP to manage routes ? BR
Hey,I'm doing a test lab where im messing around with authentication for different protocols like OSPF. But i cant seem to understand how it works. Authentication is verifying the device you're talking to is actually the device you thin you're talkin...
Resolved! OSPF Router ID
Hi..We have several interface ip address like in the picture, and why router id of my ospf is 10.103.242.5 and not using my loopback ip address?
Hi all,I have a ASR1001 pppoe server with 2 wan interfaces. Routes manage by ibgp.I would like to use loopback ip for in/out traffic and use it like pref source. Need this because Radius in this way will see only one IPTry to use RMAP but I cant find...
I have following configuation. I dont have any access list or any thing. simple router configurationTunnel connection with my hub (ipsec)crypto isakmp policy 100encr aesauthentication pre-sharegroup 2crypto isakmp key sams@ng address 0.0.0.0crypto ip...
Resolved! OSPF Area
Hi.. We configure ospf on each interface like this interface GigabitEthernet0/0/0ip address 10.103.245.13 255.255.255.252ip ospf network point-to-pointip ospf 100 area 0.0.0.0negotiation autointerface GigabitEthernet0/0/1ip address 10.103.246.13 255...
I am configuring a 2901 ISR with an EHWIC 4G LTE Verizon module for the first time. I've followed the configuration instructions but I'm having trouble with the interface changing state to down every 30 seconds or so. The dialer ...
I have a following scenarioi want my client computer to access or go to internet from another static ip from the poolclient IP: 10.20.1.2 with gateway as 10.20.1.1Router IP: giga 0 (10.20.1.1) and giga 1 (192.168.1.1) IP Pool: 192.168.1.1-4
I attached the packet tracer file, wondering what I'm doing wrong because I've tried so many things and it just doesn't work, can't get any pings working and if I do the ospf neighbor command it shows nothing. If someone can check the configs and tel...
Resolved! 1841 router <--> home router
Hello,here is a simple setup. The home router is also modem/gateway and has its own DHCP server.How do I get the home router to recognize the network 10.0.0.0/24, it does not have the possibility to enter static routes.Ping is possible in the 10-netw...
My question might sound very dumb. I have started working for an ISP. Our ISP routers run BGP with the transited provider. We are getting massive amount of routes from our provider. My question is how did the transit provider transferred routes from ...
Resolved! default route practice in ospf
Hello Hope you are all right. I think I had readed most of below link. https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/16437-ospfdbtoc.html?referring_site=bodynav I have some question about practice. Hope can have your adv...
Resolved! OSPF
Alright so I have a question regarding OSPF and areas.In this example, we have all switches running on L3 and they're handling the routing and they're all meraki.I have a main site which has stacked switches then we have direct trunk links going to t...
