gues if i want to block two network 192.168.1.0/24 and 192.168.3.0/24what will b ethe access list for that keeping in mind that i want to get the job done in one line (access-list staement) and can someone please tell me how you did that....thanks
gues if i want to block two network 192.168.1.0/24 and 192.168.3.0/24what will b ethe access list for that keeping in mind that i want to get the job done in one line (access-list staement) and can someone please tell me how you did that....thanks
We are setting up a Cisco Secure ACS. The server and ACS software has been installed. We have a lot of users, user groups, devices and even device groups. We want to add everything to ACS in a hierarchichal manner. Please let me know how to go ahead ...
Hello All, Can someone please help clarify the difference between:network 0.0.0.0 0.0.0.0 area xxnetwork 0.0.0.0 255.255.255.255 area xxWhen advertising networks in OSPF?Many thanks in Advance
"Dear All,"in one of my customer place we are facing some ISP failover issue.below is the Network Setup details1) we have airtel internet lease line with static public IP with /302) this airtel links connect to Cisco router 2801 with3) the router 280...
we are migrating from atm over shdsl to ip over shdsl. we are encountering line flapping on the shdsl line. our routers are 2610 xm with ios 12.3 T advanced security
Hi all,I'm looking for a router under $500 which connect 3 different networks together.I have an network application running on a laptop. I plan to have my laptop communicate with 3 different networks. I think a router is the device I need.Anyone kno...
Hi to all,I have this message in the router ->System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)TAC Support: http://www.cisco.com/tacCopyright (c) 2003 by cisco Systems, Inc.ERROR: No system memory detectåSystem Bootstrap, Version 12.2(7r...
I'm currently studying ISCW and have been reading the official exam guide. In chapter 5, it talks about the setup of NAT, DHCP then config a default route for the SOHO network.I have an older 2611 router running at home with NAT and DHCP. It is bein...
We are presently using the config below to connect our Branch office1 LAN to the Head Office. We have Cisco2800 at Head office and Branch office1.We want to connect the Branch office1 to another Branch office2. the Cisco 2800 we are using has only 2...
Please find the attached detail of Our scenario:we have following devices1.uc5202.cisco 2924 Switch3.Two analouge phone lines came from PBX4.Rightfax server5.two cisco ip phonesWe want to send Fax over Ip with the help of uc520 for both inbound and o...
I'm planning on ordering a 6503 with Sup32 PISA and terminate a subrate GE (150M) on the Sup card (it is the 8 port x GE)..can I do QoS with this config?
I have a problem where a route entry is not appearing in the ospf database. My understanding was that the database would populated with all entries to a particular destination and would then install the preffered route into the routing table.I have a...
Hi allWhen I connect to the switch on my cisco 877w i get an ip address but when I try browse out I am not getting natted. can you tell me why plesae?HQADSL#sh runBuilding configuration...Current configuration : 3182 bytes!version 12.4no service pad...
4w6d: OSPF: Rcv pkt from 10.205.32.2, Vlan1, area 0.0.0.0 : src not on the samenetworkPlz find the error messagesuggest me
hi, i have 3845 router with two gigabit interface and one serial interface. when i issue sh running command the output for those interfaces is as follows.interface GigabitEthernet0/0 description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$ ip address 2...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-12-2025 08:54 PM | ||
01-11-2025 12:21 AM | ||
01-04-2025 06:17 AM | ||
12-23-2024 12:46 AM | ||
12-18-2024 01:32 AM |
User | Count |
---|---|
10 | |
7 | |
3 | |
3 | |
2 |