Hi, I just wander if somebody could help me to understand IP Precedence configuration on Cisco ISR. Basically following Cisco documentation (https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/qos_plcshp/configuration/xe-3s/qos-plcshp-xe-3s-book/qos-pl...
While in discussion we are unable to conclude why BGP is Application layer protocol?? We know it uses tcp port number 179 and when tcp is used it should be transport layer protocol. Any good documented answers?
"The routers should be using the CISCO default layer 2 WAN protocol" Which protocol is the default layer 2 WAN? Now I am a bit puzzled. Does the above statement means I should use a default route between routers with known ip addresses? I actually es...
Hi all,First time posting, so I apologize if I forget any info. I've ran into a big of a snag while trying to set up a secondary ISP on my network. We've been having issues with our main ISP for a while now, so we got an AT&T circuit brought in as a ...
Hi, I need help, I have a router 7200 Software (C7200P-ADVIPSERVICESK9-M), Version 12.4(15)T17, and after a power failure in the area it did not turn on anymore, what would be the fault?
I'm having a DHCP problem with a configuration I know should work. Currently I have an ASA 5505 sitting in front of my ISP's wireless router. Int VLAN1 is DHCP client getting an IP address from my ISP. and int VLAN2 is DHCP server giving the ISP's wi...
Hello everyone! I'm working on a lab and I can't connect my wireless router to a pc. It seems that there is just no link between the router and the switch.My lab says that I should have a wireless router with the following settings:SSID - testChannel...
Hello All I would like to extend the ip address range for the router, but not working like i though it would. ip dhcp pool Poolimport allnetwork 192.168.35.0 255.255.254.0default-router 192.168.35.1domain-name gleamnsdns-server 8.8.8.8 4.4.4.4lease 0...
Hi everyoneI have to do some routing troubleshooting for one of my assignments. I was provided a PKT file which I have attached. The routes don't work as expected and I have to troubleshoot the issue. After adding a few static routes and implementing...
Hello all,I am doing OSPF config.Fortinate is connected to Core Switch, using deafult route.On Core Switch has many static routes, I want to Redistribute Static route into OSPF and filter Static route using access list and route-map.But in ospf defau...
Hi everyoneI am building a simple network for one of my assessments. I would like to get the pc's to be able to communicate with the servers SydSVR and INTERNET on the remote networks. I have tried adding a static route on SYD-R1 through its s0/0/1 i...
Hello Techies,I need your help/suggestion which protocol is best suited for the attached topology.I have 2 ISP connection. Primary internet connection is ISP1 and 2nd is for failover.Scenario 1: If primary internet goes down traffic automatically shi...
Need some assistance in configuring the ASR1006Redundancy: What is the better approach? Redundant 1006 or use two (2) 1006 devices in redundant setup?Module Sizing: From a growth perspective would it be better to offer 100GE configuration? Is there a...
Hey I have put a router (ROUTER-PT) in Cisco Packet Tracer and I am not able to connect more than 2 interfaces to other devices.It says "The cable cannot be connected to that port".
Hello, dear experts I have a little bit of an issue with cisco static pat. Basically i have some hosts on the remote network <site outside ip>, in the inside segment 10.0.0.0/8. Hosts need access to the internet and I need access to some ports from a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-14-2025 01:24 AM | ||
| 06-06-2025 12:18 PM | ||
| 05-15-2025 07:28 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM |
| User | Count |
|---|---|
| 10 | |
| 4 | |
| 3 | |
| 3 | |
| 2 |
