Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi folks:I ordered a Catalyst Express 500 (WS-CE500-24LC) for a branch office we are putting in our 1st VOIP phones for. We'll have about 4 phones, 10-15 workstations. We've ordered a Split T1 (PRI 6 channels, Internet access 18). This will be an eth...

Just a general question that I never understood.My guess is because a T1 goes over a pots line that has multiple repeaters to keep the signal alive.I know you can run phone over ethernet and ethernet over phone line so they are interchangable.Any ans...

jenderlin by Level 1
  • 1122 Views
  • 10 replies
  • 0 Helpful votes

Hello,I was wondering if when using Layer 3 VLAN routing, by using the rate-limit command, does it successfully rate limit the traffic when you have CEF enabled.My thought was that when CEF is enable, some traffic will not need to touch the VLAN Laye...

I am running RSTP and want to ensure that this will provide my desired results. I want all vlan traffic to flow to the core (6500's) from the DCU switches (6500's) with the exception of vlans 10,11,19,20,30-32. I want these vlans to flow through ...

mcroberts by Level 1
  • 741 Views
  • 7 replies
  • 0 Helpful votes

TOMCAT mod_jk.so now exist in our WCS v4.1.83.0. The fix is in the 4.1.92.0. Is it necessary to de-install 4.1.83 before installing 4.1.92?Is this upgrade really necessary?

bleejr by Level 1
  • 329 Views
  • 1 replies
  • 0 Helpful votes

Hi, I have a Cisco 877 configured in VPN mode to connect to a Cisco Concentrator. The ISAKMP policy is AES-256/SHA and DH group 5.Now first of all the 877 will only connect as a VPN if I set both the concentrator and 877 to DH Group 2 and when I loo...

whiteford by Level 1
  • 860 Views
  • 7 replies
  • 0 Helpful votes

Hi,I have configured the Cisco 3825 router as a DHCP server for leasing an IP addresses to me remote intra network.How many IP address can this Cisco 3825 router can lease?Thanks and Regards,S.Venkataraman.

Lavanholy by Level 1
  • 525 Views
  • 4 replies
  • 0 Helpful votes

I'm taking a semester long BSCI course one thing that me an another classmate were debating was why would you want to run OSPF over Frame Relay versus just using static routes.The networks on the other side of Frame Relay cercuits seem to usually be ...

I have a new 2811 running IOS version 12.4(15)T3. I have installed AIM-ATM-4T1 module and am using controller T1 0/0/0 as the only active connection at this time. The AIM has the green LED in slot 0, when the telco circuit is plugged in I have CD and...

steuber by Level 1
  • 1874 Views
  • 3 replies
  • 0 Helpful votes

Greetings all - I'm testing different scenarios with ASA redundancy, and OSPF routing on the inside segment. I'm connecting the inside interfaces of the ASAs to the core switches, and I would like to avoid enabling VLANs and trunking between them. ...

I have a question regarding running BGP on a router with two VRF's:Here is my config:!router bgp xxxxx no synchronization bgp log-neighbor-changes network x.x.x.x mask 255.255.255.x network x.x.x.x mask 255.255.255.x network x.x.x.x mask 255.255.255....

Hi. I'm having trouble coping files over the WAN using IPX as communication protocol, some times everything works fine put others the files doesn't copy complete. If I use TCP it always work's well, the problem is that the company were I work insist ...

I'm trying to rate limit ftp and www traffic out of our 20mb/s connection. The goal is to not let downloads exceed 2mb/s. Here is what I'm using and it doesn't seem to be working (router is a 2811 running 12.3(8)).access-list 103 permit tcp any any...

0rsnaric by Level 1
  • 2102 Views
  • 4 replies
  • 0 Helpful votes