Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! IP multicast commands

I must be hallucinating or something. Where are the commands ip pim dense-mode and ip pim sparse-mode and ip pim sparse-dense-mode in the Command Refs?Kevin DorrellLuxembourg

Aironet 1410 Wireless Bridge N Type Converter

Hello,We bought Aironet 1410 Wireless Bridge ( AIR-BR1410A-A-K9 ) but this product does not suitable to our project, actually we need Aironet 1410 Wireless Bridge N Type ( AIR-BR1410A-A-K9-N ) Does Cisco has any interface converter to N Tpye?(We cann...

Dual ISP - Load sharing/balancing

My organisation is implementing a secondary ISP link (4Mb) to coexist with our primary ISP link (10Mb).The powers above would like to make use of the 4Mb link rather than have it sit there purely for redundancy.We are undergoing the process of reques...

SW6509 detected GLC-LH-SM with bad EEROM

Hi all,When I installed new GLC-LH-SM to card WS-X6724-SFP on sw 6509, the switch disabled interface and gave an error message: "%PM_SCP-SP-3-TRANSCEIVER_BAD_EEPROM: Integrity check on transceiver in LAN port 1/20 failed: bad key".It also had the sam...

ospf area issue

Hi allIn ospf process,they require inject a default route to area 4, should i configurate the area 4 is a stub or totally stub area?one more a question:if i wanna an area in ospf process can only receive the inter-area route and must not receive the...

Problem in Router 1841 - Route-map function

hi , everybody please help me in cause,in my school has 2 adsl [dynamic IP from ISP] i connect 2 line into my router [R1841+2WIC-ADSL] my config in file. if 2 link is normal, everything is good butin case when link 1 down, service in route-map on lin...

sweetpigy by • Level 1
  • 1185 Views
  • 6 replies
  • 0 Helpful votes

NAT problem

Hi All,I have been stuck with NAT problem. It gives me a error my ASA. like thisNo translation group found for icmp src fugen-dmz:172.16.2.253 dst outside:4.2.2.2 (type 8, code 0)These hosts are coming from interface etherent0/3 (named as fg-idsys) o...

caliber01 by • Level 1
  • 2168 Views
  • 10 replies
  • 0 Helpful votes

Resolved! BGP and regular expression

Hi everyone not sure if this is the right place to put this but I have a BGP statement that I'm trying to understand..it is as follows:neighbor VNET filter-list 17 outip as-path access-list 17 permit ^[0-9]+$ip as-path access-list 17 permit ^$what is...

wgranada1 by • Level 1
  • 1088 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Cannot configure ppp multilink group 1 on 2621

I cannot enter this configuration for new multilink ppp T-1:interf multlink 1 ip addr n.n.n.n n.n.n.n .. ppp multlink group 1int s0 ppp multlink group 1The "multlink group 1" syntax is rejected, interface mult 1 is always down/down, and interface vir...

cshirkoff by • Level 1
  • 1108 Views
  • 4 replies
  • 0 Helpful votes

question...

1. what doest ip classless command do?2. what would be one of the down sides of upgrading a network composed of Cisco 2500 to OSPF?

Shadow MPLS port concept

HiA client has asked for 'shadow MPLS port" for their DR site. This query is not very clear. following is the scenario:They have two service provides (VPN). They want to have links from both service providers (they will be primary at some locations a...

WAN QOS Question

I'm looking at configuring QOS across a frame-relay WAN. We have a 1536 Port/768 PVC. My question is does the router base the bandwidth percentages on the port or pvc speed? Thanks in advance for your help.

Load more