hi guysi want to system bootstrap using rommon mode,any hint?
hi guysi want to system bootstrap using rommon mode,any hint?
hello guysi have a 6509 core switch with sup2my pcmcia storage is 256MB.but when i insert the disk inot sup slot the device can not detect it,it goes to rommon and nothig will happen.any idea?
Hi All,I have one Cisco 1721 which was working fine w/o any problem. But some days back due to unable to recall password being set into it, I just booted the Router with pressing Ctrl + Break key to go to rommon prompt, but it gets hanged.Then I star...
I have router with ospf and bgp process run.At first step i don't do redistribution between process. Here part of config-router ospf 1 log-adjacency-changes network 2.2.2.0 0.0.0.255 area 0 network 172.22.23.2 0.0.0.0 area 0! router bgp 65334...
I have two regional offices connected Via serial Modem on a clear channel, in the main office I need to setup the internet conection in order to works simultaneously with the corporate conection. The corporate is Using the clear channel via serial po...
Hi, Have a polycom vsx 8000 between a 2800 (C2800NM-ADVSECURITYK9-M), Version 12.4(12a) series router and a 1811 router. the quality is fine,but after 60 minutes (exactly) the call will drop. We are using dynamic ports on the polycom. Does anyone ha...
Hi Experts,I would like to check if 2 Routers running same EIGRP statement can be connected to same switch? Will there be any routing loop and how can routing loop happens? (side question)Thanks..
Just wondering, are there any guides or helpful documents on distinguishing and defining error event logs? Basically, what they're indicating, the reasoning and possibly the fix??I have a bunch of examples which I have attached to this post in .doc ...
I just got a 2811 IP base image router and put in a new HWIC-1FE card but the router seems like it does not recognize the card.The lights on the card turn on but I cant see the interface in the router. So far I tried putting the card into slot 1 and ...
Hello, I am in the process of replacing my telco provided ADSL PPPoA modem/router for a Cisco unit. What I need is the following is:ADSL PPPoA modem/router function,Mac based ACL & DHCP.It's main purpose is to provide internet access, DHCP & Mac Base...
Dear All,I would like to ask you that on ASA 5500 it can support PPPoE or not?if can, How to configure service PPPoE?Best Regards,Norung
I currently have two different routers each with a bonded circuit to the same AS number using BGP. I want to combine them into one router. Can I have a neigbor statement with different ip's and the same AS number? Also, can I create a second loopback...
I am working with 2621xm IOS (12.2(15)T10)and I am looking for a basic QOS configuration to use so that I can prioritize traffic from my inside network to an external host IP. Below is what I think should work...please provide any suggestions/feedbac...
I have some servers at a co-lo facility and I want to change from a SonicWall to a PIX 506. I have a range from my co-lo of 64.X.X.225 to 64.X.X.238. I currently have the SonicWall at 64.X.X.225 and my servers all have public IP addresses.Since the S...
Can't seem to get this to work, need remote connections on port 22 (800 series).
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-05-2024 05:56 AM | ||
10-04-2024 06:22 AM | ||
09-23-2024 06:56 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM |
User | Count |
---|---|
13 | |
11 | |
6 | |
4 | |
4 |