Does Cisco C899G-LTE-NA-K9 4G LTE Integrated Services Gigabit Router have @ SIM card slots?
Forum Posts
All, And to me means both or more of the object needs to be down and or means either. I have the following :Track 1 - RTR (Rechability)Track 2- RTR (Rechability)Track 3 - RTR (Rechability) Now I have track group as follow Track 100 Ortrack1Track2 Tra...
Hey everyone, I am pretty green to all this and still learning so bare with me.... I am trying to backup a RV320 router config file through ssh using PuTTY and then restore that backup config file through the CLI. I know you are able to just backup...
Faced a limitation of the EEM functionality on the Cisco C1111-4P hardware with IOS-XE 17.03 and 16.12 firmware. Missing IP SLA event detection functionalityWhat version of IOS XE should be used for this functionality to be available. sh event manag...
We have a RV340w with dual wan. Is there a way to view the external IP address of each WAN. These are not static and can change. I need to check them and update the white list on some of our external servers. I can see the IP adress that has been a...
This is a quick lab I just drafted up. The issue not seeing Loobback 0 BGP route that should have been redistributed into EIGRP on R1 or R2. This topology should cause a loop in the network when trying to reach 10.1.1.4 on R4 but that's not what I...
Resolved! Cisco homelab VLAN troubleshooting
Hello everyone I am fairly new to advanced networking concepts. I do some networking for my company but most of it is not setting up new devices or networks. Anyways, I was able to get my hands on a Cisco ISR 2921 and a Cisco 3560-x PoE L3 switch fro...
Resolved! Router Upgrade in INSTALL Mode
Good Morning...Saw this fantastic link from Leo The Legend.. https://community.cisco.com/t5/networking-documents/cisco-isr-amp-asr-1k-routers-ios-xe-firmware-upgrade-install/ta-p/4426457 Quick question, after I set the packages.conf to boot, can I se...
Resolved! Virtual Link issues
Hi all! I came across issue when configuring OSPFv3 and trying to set up a virtual link. Under regular OSPF, under ospf subconfiguration, I use # area ( # of transit area ) virtual-link and Router-ID of a neighbor. With OSPFv3 I got little lost. ...
Resolved! ISR 4331 routing table capacity
Hi Experts , I was looking for the maximum routing table capacity supported on ISR 4331 with default 4gb memory. I was unable to find any documents relevant on cisco's site. Would really appreciate any links or documents on this.
I am designing a lab topology within EVE-NG that mimic's a prod environment.. ..of course, in the real world, the prod environment uplinks are managed by BGP uplinks. My uplinks however to the WAN must be handled by my local home router. Because of t...
Resolved! CEF and DCEF
HiI am confusedd about the difference between CEF and DCEF :(dCEF) mode – When dCEF is enabled, line cards maintain identical copies of the FIB and adjacency tables. The line cards can perform the express forwarding by themselves, relieving the main ...
We have all of our distribution switches dual uplinked to our 2 core switches using eigrp.Each core switch has unique vlan assigned as the eigrp transit/uplink vlan.When doing a traceroute we see the first hop with each of the core eigrp, but one of ...
Hello experts!i am just practicing DMVPN with random topology which has 2 hub & 2 spoke. The problem is 2hub & 2spoke state is in IKE. What is the reason ? suprisingly i can ping from HUB loopback to SPOKE loopack address.NOTE: Toplogy & State:IKE ...
Hi guys, Which license is required for QoS to work on ISR4000 series routers? Is it AppX?
