I am new to cisco and here is my question I have a branch router which is connected to MPLS and Internet. A tunnel uses the internet and connects to my main office. The configuration is interface Tunnel1ip address 10.2.1.41 255.255.255.0 (This is ...
Hi,I have problem with upgrading IOS in Cisco IR829. I used image universal k9 version SPA 158-3 M2a bundle, router was shipped with older version (15.7). I run commandbundle install flash:ir800-universalk9-bundle.SPA.158-3.M2a.binRouter was doing so...
I didn't find any BDI template on vManage 20.6.2 but I could do it with CLI am I missing a thing? I believe it should be at "Cisco VPN Interface Ethernet" here right?
Hi,I will be upgrading the CISCO2911/K9 from version Version 15.2(4)M4 to Release 15.7.3M8.Do I need to also upgrade ROMmon?I've checked release notes but cannot find any information about it.I wanted also to check the system image in the Cisco IOS U...
I am trying to find a EEM Applet or EEM TCL Script for Cisco C1121-4PLTEP that can be used to do LTE Site Survey.I have tried to use one script using syslog pattern but logging buffer is missing incoming sms index messages, so pattern is not getting ...
Hello, I am setting up a 1905 router and I want to enable access via http on that router I followed the procedure described on this link https://www.cisco.com/c/pt_br/support/docs/cloud-systems-management/configuration-professional/111999-basic-route...
Dear ALL, I can use the "table-map SetTag" in BGP configuration for match community ,then set the tag number, it works. but how to apply the route -map to match tag number, then set the community. Below is my configuration. ip community-list 2 perm...
See attached diagram for details. I want R2 to advertise only “10.100.254.1/32” to R3 using a route-map. How do I do this? R1/R2 are running OSPFR2/R3 are running eBGP44/r2 are running eBGP === R2 Config === interface Loopback0ip address 10.100.1.1 ...
I am working on Cisco 1121 LTE router and logging buffered is enabled for level debugging but when I send SMS from cell phone to the router I don't receive any notification/message on console and under sh logging. Although router receive messages and...
Hello Experts,I have ISR 4461 router having 2 ISPs terminating with each has 1Gig internet bandwidth. We have failover on ISP circuits. We have below licenses pre-installed on the box.Technology Package License Information:---------------------------...
On a ASR1004 I have a 10G circuit ,it is separated into 2 VLANs. One is on TenG0/1/0.350 and the other is TenG0/1/0.450, the first hold all internet traffic while the other holds our VPN connection. It is that circuit TENG0/1/0.450 that I have ques...
I've been trying to solve the problem of a single VLAN in our org needing a different route than the rest of the traffic on the core switch. It goes to a different firewall to keep things separated. In my research, I keep coming back around to Policy...
Jun 14 23:43:29 cdt: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:3837741645 1500 bytes is out-of-order; expected seq:3837627765. Reason: TCP reassembly queue overflow - session x.x.x.x:63150 to y.y.y.y:80 What could be cause this log message keep ...
I have a Router that is connected to High Availability Firewall using 2 different interfaces on the Router. The interfaces are layer 3 interfaces with the HA Firewall. The router is receiving the internal routes from the Firewall on both Interfaces. ...
i am trying to dedicate some traffic to one ISP connection from 1 source IP (10.200.50.2/248) and the ISP IP is 45.240.181.2.I can ping from 10.200.50.2 to 45.240.181.2 but I can`t ping the ISP router 45.240.181.1?here is the router configuration.!!...
