Routing

I want to run BGP on the core switchesand eigrp internally. for this i am redistributing BGP into EIGRP so that i have a preferred path to the core.Do i need to redistribute EIGRP back into BGP so that site 1 learns site 2 routes and vice versa. IS t...

Is there any way to configure a multilink bundle with one ethernet drop link and one serial link. If so guide me with configuration steps please

Hi,A client of ours (2811 router )have a requirement wherein all voice traffic needs to take the first serial interface & all data traffic the second one. Also it should failover ie if first link goes down then voice should go with data and vice ver...

Hello everyone,Here my current situation.I currently have 3 ISP providers, 2 of them are our own and the other is provide by our parent company through the WAN link, I also Have two Physical Segments, 10.10.4.x and 10.10.8.x each is assighed its own ...

I have a 8 sites connected via 2 MPLS-VPN WAN clouds with different providers. Each site has 2 WAN routers each with a DS3 to a different provider. R1 connects to MPLS-1, R2 connects to MPLS-2. R1 and R2 connect into Layer3 switch in the LAN core. ...

I'm trying to create what I think is a fairly straightforward configuration, but I'm stuggling to find examples, etc to help me out.I have an existing router attached to a broadband device that is supplying 192.168.1.x natted addresses behind it. Wh...

How to configure router under nat for proper UDP broadcast solution under NATted environment"

Tnl 27 PPTP: Tunnel created; peer initiated Tnl 27 PPTP: SCCRQ-ok -> state change wt-sccrq to estabd Tnl/Cl 27/27 PPTP: l2x store session: tunnel id 27, session id 27, hash_ix=27 Tnl/Cl 27/27 PPTP: vacc-ok -> state change wt-vacc to estabdPPTP mgmt d...

I have an Avaya PBX with an IP address of 192.168.1.30/24. I have a reporting server with an IP address of 192.168.23.230/22. If I change the IP address of the reporting server to any other IP address on the 23.0/22 network, they can communicate. ...

I've heard many arguments on this, when configuring a static route, what is recommended for the next hop to be:a)local egress interfaceb)next hop IP addressWhat are some of the the consequences of using some remote hop (hops away) as a next hop on a ...

I am getting an error during configuration saving using the command 'saveallcnf'Creating C:/CNF/TMP/plfm:LineDrvDb.zip Open file v1_0_0/DSX3_CFG.dat in ZIPcmd controller detected ...................cmd controller detected ...................error in...

Hi,I am a bit confused with the prefix list. Say I have "permit 10.16.0.0/14 le 21", what does it mean?Thanks.

Hi team,I have a core switch 3750 stack with G0/0 going to firewall-1 and G0/1 going to firewall-2 and G1/0 going to another router that has a network of A.A.A.0/24 ; B.B.B.0/24 ; C.C.C.0/24the scenario would be the internet traffic should pass throu...

Can anyone explain , what this interface output actually means????What does output drops indicate?????Input queue: 0/200/13108178/666 (size/max/drops/flushes); Total output drops: ...

I am trying to set up 2 DSL connections and a cable connection in my home. I have been looking at load balancing routers, including 1751. However, I connect to work through Cisco VPN (VPN client version 4.8.01.0300). Will this tunnel be load balanced...