Hi all, I have OSPF set up between 3 routers and R2 keeps going with: state Speak -> Standbystate Standby -> Activestate Active -> Speak over and over. Neither R1 or R3 has this issue. Here is the topology: And here is the ospf section from "show...
Forum Posts
Hello all. We have followed the process for Password recovery, but all the box does is boot back in to rommon mode, nothing else. Also, if No password recovery was entered in to original config, how can we restore if this was the case? Thanks i...
1. Configure R13 as PPPoE Server 2. Configure R14 as a PPPoE client 3. The link must be up even if there is no traffic 4. R14 must always receive the ip address 131.131.34.4/32 from R13 5. Do not use DHCP to assign the ip address 6. Avoid unneeessary...
Hi, I'm studying for my CCIE and exercising with EIGRP. All my exercises are done in CML2, using IOS Version 15.9(3)M3. In my last LAB I was playing around with different paths and how adjusting the metric changes the FD, CD and RD. The Route...
Hi Guys/Gals, I am having trouble understanding the use of ACL' s in SNMP groups and can't seem to find the exact answer. The thing is we use SNMP groups for custom views and we would like to limit access to trusted sources via an ACL. Howeve...
CSC Can you explain why i have dual CSC profiles and as such dual posts
Hi all, I have a question regarding ASR1001. we have used the current 2x10G ports and planning to upgrade other ports to 10G port too.i have read datasheet ASR1001 and is it possible SPA slot to support ASR1000-ESP20? i just want to confirm that only...
Resolved! ISR 4331 SFP
Hi Folks Wonder if you could help have an ISR 4331 with an SFP (SFP-GB-GE-T) in interface G0/0/2. It is set for auto negotiation and negotiates to 100M/Full duplex to an ADVA NTE. Although the interface comes up I am seeing CRC errors. The circuit th...
Resolved! BGP Global RIB vs Adj-RIB-Out
) Now in the snippet below step 5 mentions "Install the best-path route into the global RIB, process outbound rules... then advertise to BGP peers" My question is this statement referring to the best route being advertised from the global-RIB or the ...
how to connect this router (the one at the top) to the 3 switches at the bottom, these are 2 different networks with 2 different subnet masks. I did the interface encapsulation but it doesn't send packets from any pc in Sales & Marketing Network (the...
Hello, l need to advertise by BGP two host IP addresses for example 1.1.1.33/24 and 1.1.1.34/24, they belong one subnet /24, terminating on subinterface. I need to advertise 1.1.1.33/24 to one bgp peer, 1.1.1.34/24 to another bgp peer, but in routing...
I am working on getting my router and switch to work with my cable modem. I have gotten the router to see the outside world and ping addresses. I am now working on the switch and having issues. I have my router connected to port 24 on my 2950 ci...
I have openvpn client on Windows 11 which started to sometimes work and sometimes not (after years of working ok). Two changes I made were windows upgrade and getting a Dell docking station with UTP jack (before was always wireless). I found out if I...
Im new to Vlans and static routing. I got assignment that have scenario like this :There's two building 1 is "Teknologi Maklumat" and 2 is "Matematik" and each building have 3 vlan. I know how to make vlan for each subgroups. But i dont know how to m...
Resolved! Can't enable boost license 4321
Can't enable boost license config)#platform hardware throughput level boost not available. FLM240302GF_20220520020540.lic was installed and Version 16.8.3 Fuji I thought was the requirement, what am I missing. Index 11 Feature: booster_performanc...
