Routing

I've a branch office wan connected to the main site using only static routing.In the same router, Cisco 1760-V, I've an Adsl Internet connection with a VPN configured to the main site.We'd like to use this link only when the primary wan connection is...

hii currently have cisco pix 515e, restricted license w/ 2 interfacesi also have 2 internet connections100mbps as my primaryand t1 as my backupwhat i would like to achive is to have automatic failover in place in case if our 100mbps line goes does it...

I am having as5300.On one fine day it has gone in a RTR1(boot)> prompt after power on reset.It is not going to normal mode.I erased the entire flash: and tried to upload the compatible IOS image.Through tftp entire image is getting transferred but af...

what is exact use of Cisco LAN extender?as per its name its extend the brodcast domain of one lan to the remote lan?is it possible to configure through WAN link and can i extend my LAN to remote location?what kind of interface it is having?and are al...

Dear Professional,I have a 7609 router with 9 module. I have WS-SVC-CMM Module installed in module 1 & 2 both of them are equipped with (1) WS-SVC-CMM-6E1, (1) WS-SVC-CMM-ACT and (1) WS-SVC-CMM-24FXS.I will replaced the old 3660 router with 7609 rou...

Dear All,We got 2 catalyst 403 (4012-SP module)switches and both SP modules in faulty status but in the same time the switches working very well, i didn't find any doc to explane the reason behind such status so is there is anybody know the reason be...

Hi, I have a PIX 501, running 6.3(5).Our ISP has done away with bridged connections, so we're forced to setup PPPoE. Works fine when I take my modem out of bridging mode and get it to do the work. My relevant config:vpdn group pppoe_group request dia...

I wish to get some validation of the design. I have two(2)10K's routers and two(2)6500's switch(layer 2 only). The switches have more than 110 VLANS split odds switch 01(pri) and evens switch 02(pri).The evens VLANS are given a lower priority on swit...

In my previous job we used a SonicWall as our firewall and web content device. Since the PIX515E doesn't do content filtering (I can't afford websense!) I was wondering, could I somehow string the PIX and SonciWall together? Or should I work on eli...

Can I use HSRP VIP as the source address for a GRE tunnel. It does not work for me, when the active router goes down (hard down) the GRE tunnel does not work on the standby router, even though the HSRP becomes active on the standby router. Thanks in ...

Dear All, I am not getting console of NPE-G1? I have tried different baud rate but it is still same ..The PA installed in 7206 are getting detected since EN led is glowing ...regds,aman

i have a directly connected network (T-1) 172.19.1.1 and from the router i can ping only some devices on the 172.16.1.0 network. i have a route in the routing table for the 172.16 network. i can ping their defaut gateway which is 172.16.1.1 but i can...

Hi folks,what seems to be the common cause of core switch hang-up? Could you please advise, what is the best tool to monitor, imminent switch failure? Thanks a lot.Vlad

Hello there, I will like to know if some of you can share a Best practice using 3 different platforms (Alcatel, Nortel and Siemens) over a Cisco ISIS Network. Right now we are using that scenario, but we are having a lot of issues trying to add more ...

I am wondering if it is possible via configurations to make sure that IPSEC processing does not off load to the main processor in the case of VAM card (Encryption Card) failure. Or if it is possible to have a secondary VAM card in the 7200 Chassis. (...