Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Resolved! NHRP issue

Hi all,I have problem when I doing DMVPN lab.I configure the hub and spoke router.The spoke router is working. Use "sh dmvpn" can see output and can send NHRP Registration request to hub router.But "sh dmvpn" and "sh ip nhrp" show nothing on the hub ...

hello,i have catalyst 4000 series core switch and couple of access switch.past few days we have connectivity issue and servers are out of connectivity (ping fails 80 or 90%) today i check the core switch using serial link. we have only one default va...

feroz syed by Level 3
  • 1768 Views
  • 13 replies
  • 0 Helpful votes

Hello team, I want provide little tuning of nat statements . Situation: host a.a.a goest to -----> x.x.x ---->DNAT to y.y.y (everything works) BUt in situation when is DNAT y.y.y unrecheable i want change nat statement to : host a.a.a goest to ----->...

I have a scenario where I am learning a lot of different networks via BGP. Without going to far into the design/requirement, I am needing to only advertise a specific IP from these networks learned via BGP, and not the whole network.For example, I am...

Have a requirement were multiple vedge devices are connected behind a NAT device.According to Cisco Documents Port offset should help in these scenarios. https://www.cisco.com/c/en/us/td/docs/routers/sdwan/configuration/sdwan-xe-gs-book/cisco-sd-wan-...

port offset .png
VKN by Level 1
  • 548 Views
  • 0 replies
  • 0 Helpful votes

We have a fiber loop connecting about a dozen school buildings.  They have all been running 3850's up until earlier this year, when we started upgrading.  One location now has a 9300 stack.  All of these switches, including the 9300 are broadcasting ...

Resolved! Cisco Umbrella

Hi Team,Greetings!!Below website is categorized under online Communities but still the website is blocked under Gambling in cisco Umbrella. Could you please check and help on how to proceed further.URL:  http://www.slotimports.com ThanksWKH

WKH_1-1623730179264.jpeg WKH_5-1623730423958.jpeg
WKH by Level 1
  • 854 Views
  • 1 replies
  • 0 Helpful votes

I am trying to configure BGP based routing between two sites using two ASA 5506Xs. Routing between most of the sites works fine. The one exception is the VPN networks. The subnets are configured using the Client Address Pool setting in the AnyConnect...

Hi, i am trying to create a L2TP VPN connection for user to remote connection back to office. can i set ip unnumbered GigabitEthernet5 ?can I set in this way? or I have to create the loopback?i am not sure which ip route i should create. please advis...

T0mTheCat by Level 1
  • 1663 Views
  • 2 replies
  • 5 Helpful votes

Hi everyone, I'm  trying to use nat on a catalyst 1000 Series.I've configured 2 vlan; one with ip nat inside and another with ip nat outside.I've configured an acl as well. Nat do not work, when i'm using wireshark i see outcoming packets source with...

RT74693 by Level 1
  • 2574 Views
  • 3 replies
  • 0 Helpful votes

Hi, I have configured some Public loopbacks on my router and when i try to telnet to my router through the Local network it can let me go inside but when i try to telnet router through these Public IP from outside then it is not allowing me. this hap...

Hi all,The following simple configuration run flawlessly on my C1111-8P and IOS XE 16.  As you can see, I have a trunk ethernet port connected to a switch feeding my router with two VLANs (1 and 2).  And both of my VLANS are bridged on two separate B...

leosoft by Level 1
  • 4848 Views
  • 6 replies
  • 0 Helpful votes