Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

Hi all, I'm currently experiencing Network Problems between two Datacenters which i can't make sense of. I banged my head for days on this.  About the Setup: Datacenter in Germany has a Cisco ASA 5525-X (9.8.4.32), US Datacenter has a Cisco ASA 5516-...

Hi all , I'm a litle bit lost regarding bridging vlan on my router ASR1111 (IOS-XE, no more IRB support).I have read about BDI, and i'm trying the get a grasp of it. The point is I would like to bridge vlan through my router on specific interfaces fo...

r1.png
Bob_Rock by Level 1
  • 3481 Views
  • 14 replies
  • 0 Helpful votes

Can anyone help find some documentation on some bgpsec configuration. Struggling to find proper documentation to help with syntax etc with bgpsec config on CISCO routers.  Any help appreciated have looked all about the internet but can't find anythin...

JLOU1234 by Level 1
  • 877 Views
  • 0 replies
  • 0 Helpful votes

HiI built an EEM menu into my routers to expedite results.  Currently -below- is my IPSec MENU. This EEM script is 4+ pages long and thus would like to modularize the menu into separate modules for ease of updates and any EEM troubleshooting. In my a...

fsebera by Level 4
  • 946 Views
  • 2 replies
  • 0 Helpful votes

Can anyone help me to find some examples or lab books which include bgpsec AND bgp with rpki. I have searched the internet and cannot find anything to help me start my experiments for my dissertation.  Any help is appreciated, finding loads of inform...

JLOU1234 by Level 1
  • 2854 Views
  • 4 replies
  • 5 Helpful votes

We have added an IP security camera at our office that can be viewed from the outside on a mobile device.  I'm not comfortable leaving this up for too long without some type of separation from our office network LAN. What would be the best way to onl...

getRdone by Level 1
  • 921 Views
  • 3 replies
  • 0 Helpful votes

HiI am trying to get my head around layer 3 switch routing and am missing the link between vlans and ports.I'm configuring layer 3 with SVIs.My switch is an SG250-08HP.  I have exec  IP routing.I have added a vlan 10,20 with no shutdown and the switc...

admin28373 by Level 1
  • 6066 Views
  • 16 replies
  • 0 Helpful votes

My CE router is sending plenty of subnets to PE. I have captured .pcap file of BGP update and I would like to see one of specific NLRI information form the pcap file. When I have opened the pcap file there are plenty of NLRI info .How can I filter fo...

I have 5 L3 switches that are all connected to each other with routed links. Each of the 5 locations has its own L3 switch. All switches are using OSPF and see routes to each other. One of the switches physically went down. A couple of the switches w...

Hi, I have just bought a Cisco C899G LTE, with the 4 pin square power plug. The router does not have a power brick with it - does anyone know what the pin-out is so I connect a temporary PSU? Cheers, Bill

radiomean by Level 1
  • 1067 Views
  • 2 replies
  • 0 Helpful votes

Hi, We have 49 HSRP groups on one interface of our current routers and need to migrate to the 4451's, but the limit appears to be 25. Does anyone know if this is a hardware limit that won't be increased or if there is a possibility for a firmware upg...

Cannoo by Level 1
  • 1724 Views
  • 4 replies
  • 1 Helpful votes