Resolved! ACL question
Hi guys,Can someone tell me what is the difference between these two extended ACLs?1) permit udp any range 8801 8810 192.168.0.0 0.0.255.2552) permit udp any 192.168.0.0 0.0.255.255 range 8801 8810 Thank you!
Forum Posts
I am trying to demonstrate weaknesses of BGP, I am doing this in GNS3. I found prefix hijacking fine to implement as there is a lot of documentation on this. I am looking for help with malicious bgp route leaking or malicious blackholing. Not alot of...
Hi, I am trying to route traffic over to a different subnet then out to the internet but unsuccessful at doing so.I am not sure what I am missing? I have a gateway configured on the Cisco (172.16.5.95/22) router pointing to my ISP router (172.16.5...
Resolved! Cisco C927 with Virgin Media connection
Hi all, I think I am missing something really obvious in my config to get my router to work on a Virgin Media fibre connection.Would anyone mind taking a look over my config and pointing out the obvious bit, which is stopping my router from getting a...
Hello I have a 192.168.1.0 subnet from an ASA 5508-X (GE0/2) going to a Catalyst Switch for it's own management / Internet access from ASA IP which has a 192.168.1.5 IP Address assigned manually via vlan 1. I have several Interfaces dedicated to that...
Resolved! Auto QOS cisco 3650 IOS XE 16.6.7
Hello Community, Actually am working for QOS project for Snom phone and Microsoft 365 traffic,we decided to Mark traffic from the terminal (IP Phone and PC with GPO)in access layer we have cisco catalyst 1000, then I configured "auto qos trust DSCP" ...
Hi allI recently purchased CISCO RV340 to use with two internet connections, Both are lready connected to a Modem and then its been looped CISCO RV340 as a WAN connection. WAN 1 is working when its connected directly but not via this router. Can some...
So I'm trying to think of a way to do this and have been messing around in gns3 a bit but I figured I'd post here for ideas while I putz around. 2 internet routers that connect to 2 different ISP's. They share the BGP tables. Right now, those go ...
Afternoon AllIve been at this task for weeks on and off. What I thought was a simple setup has got me stumped. from the router CLI I can ping 8.8.8.8 but not from and ofthe hosts. Below is my router config, its now all over the place due to my consta...
Hi All, Just looking for advise , pros vs cons about connecting an ISP internet feed directly to our core mpls/vpls switch. ISP Internet Router—>adva—>Core Switch(siteA)—>mpls/vpls—>Core Switch(siteB)—> Palo Alto The PA firewall will have a separate...
Hi, Is it possible to configure DNS-name in access lists in ASR1006-X and ISR451-X like in ASA as shown in this link: https://community.cisco.com/t5/security-documents/using-hostnames-dns-in-access-lists-configuration-steps-caveats/ta-p/3123480 Does ...
Hello Community, I'm working on the setup of a Cisco CSR. I have a route 10.0.0.0/24 learned by a BGP session on tunnel 200 and 201 (MPLS and failover), I also have a static route 10.0.0.0/29 (smaller than the previous one) to a tunnel 202. I need t...
Hello Everyone,I'm setting up a lab with intervlan routing. With 2 hosts, Cisco SG220 switch and a Cisco 1941 router. I added the topology. On the switch Gi1 is an access port in VLAN 10 and Gi2 is an access port in VLAN20. WS1 is connected to Gi1 an...
Hello. I am trying to get my first vlan setup to work and cannot inter vlan route. I can't see what I'm doing wrong at this point. Can you help?Edit: The switch is an SG350-28P. Latest firmeware. I'm using two SVI vlans 10 and 20. Also have the defau...
able to ssh switch 2 from pc 2 but not able to ssh switch 3. can anyone tell me what configuration is needed in switch 3 so that i will able to ssh from pc 2 to switch 3.
