Other TracerouteRouting table of VIOS6==================Switch#sh IP route 8.8.8.8Routing entry for 8.8.8.8/32Known via "ospf 1", distance 110, metric 506, type intra areaLast update from 192.168.20.1 on GigabitEthernet0/1, 00:15:13 agoRouting Descri...
Router 2911When i enter "show ip int brief" command i found following result for one of my gigabit interface, Interface IP-Address OK? Method Status ProtGigabitEthernet0/0 unassigned YES unset res...
Hi All,I recently got an ISR4431 router for my home lab and I can't get access to the console port, USB or Aux ports. How do these connect to the main board? I suspected a hardware problem and pulled them apart, however there is no direct connectio...
HiRecently we have Memory leakage issue on our ASR1002-X. I searched and I found following link about troubleshooting:https://www.cisco.com/c/en/us/support/docs/routers/asr-1000-series-aggregation-services-routers/116777-technote-product-00.htmlQuest...
RoutingHi Guys, Here is the requirement I have with one of the client, Existing TopologyI have couple of 2960s with LAN base image switches (currently stacked ) connected to a single router cisco 1900 series router. New Topology:We are going to repl...
Hi AllI have problem with extended access list. I'm trying to block snmp traffic to a host. All traffic falls into permit "CISCO1921/K9 c1900-universalk9-mz.SPA.152-4.M5.bin rxxx#sh ip access-lists ACLExtended IP access list ACL10 deny udp any host 1...
Hi,i want to create a SFTP & HTTPS server on a router and attache a External HDD to it so we can stor the file on the HDD. is there any router which can be support this type of thing. thanx for the help,regards,PritamJit Buswas
We have 3 internet service providers. ISP 1 and 2 both have local pref set to 200, with the 3rd left as the default. This is by design to avoid extra cost on the 3rd ISP due to bandwidth usage. I need to override this local pref to prefer the 3rd ISP...
We just got in a 9300 Cisco IOS XE Software, Version 16.12.03aCisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT9K_IOSXE), Version Everything is working fine but we have 5 Vlans setup to go to IP-helper address. 4 out of the 5 work but...
Hi Experts,Is there any changes in the latest IOS version, as when I do " sh run" , the statements below are not displaying..---examples----! Last configuration change at 01:31:17 GMT Thu Aug 30 2007 by sasadm! NVRAM config last updated at 01:31:59 G...
I have configured host name, passwords, and GigabitEthernet0 (management port) to ip address to 192.168.1.1 ! That seems to work as a basic configuration. According to chapter 5 of "Cisco 4000 Series ISR Software Configuration Guide" I tried se...
Hi all, I have been given loopback ip addresses 60.50.0.1/16 ,60.100.0.1/16, 60.150.0.1/16, 60.200.0.1/16 and i need to convert them into network address using manual summarization but i have hardly no clue how to do it. Thank you in advance for help...
I have some gateways that simply do not exist anymore in my network, but they still show up when I issue the "show ip protocols" command and I'm wondering why. Is there a way to clean these out or will they remove themselves eventually? Routing Info...
c1111 can you turn the ports of so that they dont link nor light up? i could get a c1111 for cheap but the seller has no idea and tells me the 4 ports whether link nor light up if connected there are 2 other ports which link and light up i think 1 wi...
Hi all,It is stated that the time needed to access the FIB is much less than accessing the RIB.Can some one please clarify in which physical memories are actuall RIB and FIB stored? Also the Fast Switching is considered to perform Destination based L...
