Hi All, Would like to know your inputs about this issue that I'm facing right now. So I do have 1 Cisco router configured as ezvpn client and I also have another private circuit with bgp connected to it. Both Peering (from bgp/ezvpn server) advertise...
Forum Posts
Studying for ENCOR, I ran across this question, which through me for a loop: A link-state routing protocol finds the best loop free path by using ______.a. hop countb. bandwidthc. delayd. interface coste. path attributes Answer: E I was under the imp...
Studying for ENCOR, I ran across this question: A link-state routing protocol finds the best loop free path by using ______.a. hop countb. bandwidthc. delayd. interface coste. path attributesAnswer: E I did some research, so I could clear my confusio...
Hi Guys, I'm setting up a practice network in PT (attached as zip file) and am having problems. I can ping the outgoing interface on the Router (Fa0/1) from PC0 but I cannot ping the Wireless Router from the same PC. What basic mistake am I making? A...
DearsWe have a large industrial network with lots of Connected Grid Routers (CGR 2010) distributed in vast area. The considering point is that on all Routers , a switch module ( addressed GRWIC-8PC) has been installed.We desire to implement a networ...
Hello! We have CSR1000v in production under KVM from one of our Hosters.All began with Speed Issues with uplinks (Big Jitter, Latencies etc.) After a week of troubleshooting we diagnosed CSR had 100% CPU-usage on three of eight its COREs. Further tro...
As indicated in the drawing below, we are currently connecting 2 locations on MPLS. There is a Cisco 800 series router serving as CPE in each location. The MPLS will be upgraded to 100 Mbps, which exceeds the capacity of the 800 router. Therefore,...
Hi I am trying to setup access list using the webui. I have three vlans. VLAN 10 and VLAN 20. I want to block any access from native vlan 1 to any of the vlans and also any traffic from vlan 10 and 20 to vlan 1. However do want one host "192.168.1.30...
Resolved! WS-C3850-24S DHCP-Server issue
Hi Community, I am using a WS-C3850-24S as a dhcp server to deploy other switches.Now I noticed that the 3850 provides a new IP to the dhcp client when the client is reconnecting to the 3850.In detail when I do a shut no shut on the SVI of the client...
Hi all,Currently we have a deployment with two DC connected via OSPF through a pair of LAN-2-LAN links. Both links are /30 networks part of an OSPF area 0 and adjacencies are established. But now we need to make sure that when one link fails, the oth...
I'm trying to diagnose some packet loss between MPLS endpoints. There is a Cisco 2901 on one side and a Palo Alto on the other.If I have the PA capture the traffic I will see something like 1000 packets in the capture when I open it in wireshark. On ...
Hi all, I'm checking a router configuration with follow code: interface Loopback0no ip address...logging source-interface Loopback0 I have reading about logging source-interface command and according to Cisco, using this command it's possible to forc...
Resolved! speed/duplex mismatches
I know that setting one side of a port to auto/auto and the other side to 100/full will cause problems. however can 1000/full and one side and auto/auto on the other side (both ports 1gbps capable) cause problems? and what about 1000/auto and 1000/f...
Hi all a trivial question but the Quit command to disconnect a user from a console session no longer exists? I have already seen on the internet it just gives me exit
I need help of packet tracer of this. 3 sites must be included in the network (plus 1 internet connection on the Cambridge site). Each site will have to allow bandwidth for at least: Cambridge 600 hosts London 900 hosts Manchester 1200 hosts An addre...
