Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

PPPoE not working in packet tracer

HI guy, I am configuring both the R2 and R3 to set up PPPoE between them. After I apply the script below for R2 and R3. Both routers lost connective and the R3 routing table became empty. Is there any problem with the script below? Thanks for help? R...

Can not ping source bdi interface

Hi guys,   I have 4331 router  IOSXE 17.9.4.a version I configured my 4331 ISR with Bridge domain and configured at 2 physical interface that bdi interface but when I finished the configure and try to ping with gateway I cannot ping via bdi interface...

5959 by • Level 1
  • 593 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Routing spoke to spoke FlexVPN

Hi there.Please clarify the following, I am implementing in my lab this scenario: FlexVPN spoke to spoke, using BGP regarding this link:https://networklessons.com/vpn/flexvpn-spoke-to-spoke-pool-and-bgpNow it works fine and from HUB I can see all spo...

sigcerder by • Level 1
  • 1054 Views
  • 13 replies
  • 0 Helpful votes

policy based route failover & back slow or never

Using cisco isr4300 routers. Have a simple 3-way triangle between 3 routers:RtrA--RtrB |        / |      /RtrCStatic route on RtrA & RtrB pointing to a RtrC loopback, via their adjacent links.Default route on RtrC point to RtrA.No routes exist on Rtr...

will by • Level 3
  • 522 Views
  • 5 replies
  • 0 Helpful votes

Cisco Packet Tracer

I have a Problem lauching packet tracer from cisco, Group exam the course our lecturer just enrolled us in.CCNA1-THIRDYEARS-2024, it's saying initiating connection. just like that, nothing happens 

Resolved! Problem with BGP community out

Hello,R1 is connected to R2 and uses BGP.R1 sends prefixes to R2 with community 100:100.On R2 I receive the prefix via BGP with the correct community : sh ip bgp 192.168.1.111 => Community: 100:100Now I would like to send only prefixes with community...

Resolved! OSPF area range command

Hello, I have below config in one of the switches in the network. I have an SVI in the device (interface vlan100) which has a /24 subnet. OSPF has network statement for bigger pool that is /16. Since config has area range command it is generating a *...

Resolved! ASR-920 Interface Connected Type

Hello,  I was looking for a command on the ASR-920 that would show the type of interfaces that are connected to a port. In the Catalyst switches, I could use this command "show inventory" or  "show interface status". What is the command I can use to ...

ZK916 by • Level 1
  • 539 Views
  • 2 replies
  • 0 Helpful votes

ASA

Hi @All Topology as follow,R1 f0/0 - connected to tap0 and R1 f1/0 connected to R2 f1/0 and R1 f2/0 connected to L3 f1/0R2 f0/0 - connected to tap1 and R2 f1/0 Cconnected to f1/1 of L3 and R2 f2/0 connected to R4 f1/0R4 f0/0 - connected to tap2L3 swi...

ashz14387 by • Level 1
  • 934 Views
  • 12 replies
  • 0 Helpful votes

Resolved! Basic subnetting question has me stumped

Question in Book: The following ACE is typed into configuration mode on a router: access-list 1 permit10.44.38.0 0.0.3.255. If this statement had instead used a different mask, with nothing elsechanged, which of the following choices for mask would r...

hfakoor222 by • Spotlight
  • 567 Views
  • 4 replies
  • 0 Helpful votes
View All
Review Cisco Networking for a $25 gift card